On-Screen Status Displays | Philips VR400BMG specification

On-Screen Status Displays 17

You may access on-screen status displays by pressing the DISPLAY button repeatedly. On-screen status displays may include the current time, channel, and other information.

●Press the DISPLAY button once. The COUNT on-screen status display will appear for five seconds. After five seconds, only the real-time counter will appear on the screen. This counter shows you the elapsed playing time of the tape (from the point at which the real-time counter was set to zero).

●Press the DISPLAY button once again. The CLOCK on-screen status display will appear for five seconds. After five seconds, only the current time will appear on the screen (the clock must be set). (If you are watching TV, the current channel number will also appear on the screen.)

●Press the DISPLAY button once again. The on-screen status display will disappear.

<OFF mode>

Press the DISPLAY button once.

<COUNT mode>

STOP

SLP 0:12:34

Press the DISPLAY button once.

<CLOCK mode>

STOP	5:40 PM
	CH 02

Helpful Hints

SLP

Press the DISPLAY button once.

•If the channel you select has no broadcast, the screen will be solid blue.

•You may bring up a status display at any time by pressing the DIS- PLAY button. (The exception is when viewing a still picture or a slow motion picture, or when F.FWD or REWIND is pressed dur- ing playback.)

•Channel numbers (when tuned) appear on the screen for a few sec-

Image 17

Philips VR400BMG owner manual On-Screen Status Displays, OFF mode Press the Display button once Count mode

Contents

VCR For Customer Use Warranty Verification Safety Precautions FeaturesIntroduction Declaration of Conformity Table of Contents Putting Batteries in the Remote Control Before Using Your VCRUsing the Remote Control VCR maintenance Disconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast System CH3 CH4 Plug in the AC power cords of the TV and the VCR Recording/Viewing Any Channel Cable SignalConnections Recording One Channel/Watching Another SignalCable Box/DBS Cable Hookups With a Stereo TV Below will appear Turning on Your VCR Press the Menu button until the main menu appears Automatic Channel Setup Adding/Deleting Channels Automatic Channel Setup cont’d Follow the steps below to set your VCR’s clock. Make sure Setting the Clock Your selection will flash on the screen in the AM/PM space Setting the Clock cont’d Language Selection Press the Counter RESET/EXIT button to exit On-Screen Status Displays OFF mode Press the Display button once Count modePress the Display button once Clock mode Remote Control Buttons Eject Button Counter RESET/EXIT ButtonTime Search Button Index Search Button VCR Display Panel Remote Sensor FWD Fast Forward Button Speed Button Power ButtonVCR/TV Button Play Button Rear Panel AC Power CordVideo OUT Jack Video in Jack Read and follow the steps below to play a tape PlayingVHS Quasi Play Back Sqpb 1Turn on the TV Insert a tape Recording Stopping an OTR One-Touch RecordingStarting an OTR Channels are set up Clock is set Timer Recording Enter the recording’s start time Timer Recording cont’dRepeat the procedure in to set the recording’s end time Start Time END Time Channel REC Speed SLP Cancelling a Timer Recording Timer Recording cont’d 42&5 Correcting a Timer Recording Set the program to be recorded On the satellite tuner Auto Satellite Link Using a Satellite Tuner Recording One Channel/Watching Another Press the VCR/TV button on the VCR remote control toTo return to the channel being recorded, use the TV Put the VCR in VCR position. The VCR/TV light will appear Antenna Rerecording Tape Duplication Repeat Play Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still Picture Select Picture SELECT. Then, press the F.FWD button Picture SelectPress the Play button or the Stop button repeatedly to Press the Play button to watch the tape Real-Time Counter Memory Press the Index Search button Index Search Press the Time Search button Time Search To resume normal tape playback, press the Play button Quick FindPress the QUICK-FIND button Automatic Playback Features Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel Channel 3 or Glossary Specifications Renewed Index Supplied Accessories