Pioneer A-A6-J 05Additional information, Specifications, Cleaning the unit, Amplifier section

Models: A6 A-A6-J

1 85
Download 85 pages 51.57 Kb
Page 14
Image 14
05Additional information

05Additional information

Specifications

Amplifier section

Power output specification is for when power supply is 230 V.

Continuous power output (both channels driven at 20 Hz to 20 kHz)**

THD 0.2 % . . . . . . . . . . . . . . . . . . . . . 60 W + 60 W THD 0.2 % . . . . . . . . . . . . . . . . . . . . . 45 W + 45 W

DIN Continuous power output (both channels driven at 1 kHz)

THD 0.7 %, 4 . . . . . . . . . . . . . . . . . 70 W + 70 W THD 0.7 %, 8 . . . . . . . . . . . . . . . . . 47 W + 47 W

Total harmonic distortion**

20 Hz to 20 kHz, 25 W, 8 . . . . . . . . . . . . 0.05 %*

*Measured with DIRECT button switched on.
**Measured by Audio Spectrum Analyzer

Audio section

Input (Sensitivity/Impedance)

CD, TAPE, TUNER, AUX . . . . . . . . . 200 mV/47 kPHONO (MM) . . . . . . . . . . . . . . . . . .2.8 mV/47 k

Frequency response

CD, TAPE, TUNER, AUX . . . . 5 Hz to 100 kHz SpecificationsAmplifier section dB PHONO (MM) . . . . . . . . 20 Hz to 20 kHz ±0.2 dB

PHONO (MM) overload level

1 kHz, THD 0.2 %. . . . . . . . . . . . . . . . . . . . . . 60 mV

Output (Level/Impedance)

TAPE REC . . . . . . . . . . . . . . . . . . . . . 200 mV/1 k

Tone control

Bass . . . . . . . . . . . . . . . . . . . . . . .± 10 dB (100 Hz) Treble . . . . . . . . . . . . . . . . . . . . . .± 10 dB (10 kHz)

Signal-to-Noise Ratio

CD, TAPE, TUNER, AUX (200 mV input) . . 103 dB PHONO (MM, 2.8 mV input) . . . . . . . . . . . . 80 dB

Signal-to-Noise Ratio (DIN, continuous power/50 mW)

CD, TAPE, TUNER, AUX . . . . . . . . . . .91 dB/65 dB PHONO (MM, 5 mV input) . . . . . . . . .68 dB/60 dB

14

Miscellaneous

Power

requirements . . . . . . . .AC 220 – 230 V, 50 / 60 Hz Power consumption . . . . . . . . . . . . . . . . . . 170 W In standby. . . . . . . . . . . . . . . . . . . . . . . . . . 0.6 W Dimensions. . . . 420 mm (W) x 100 mm (H) x 359 mm (D) Weight (without package) . . . . . . . . . . . . . . . 10 kg

Accessories

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Lithium battery (CR2025) . . . . . . . . . . . . . . . . . . .1 Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Operating instructions

•Total harmonic distortion** Note

Specifications and the design are subject to possible modifications without notice, due to improvements.

Cleaning the unit

Use a polishing cloth or dry cloth to wipe off dust and dirt.

When the surface is dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleansers.

Never use thinners, benzine, insecticide sprays or other chemicals on or near this unit, since these will corrode the surface.

Published by Pioneer Corporation.

Copyright © 2006 Pioneer Corporation.

All rights reserved.

En

Page 14
Image 14
Pioneer A-A6-J 05Additional information, Specifications, Cleaning the unit, Amplifier section, Audio section, Accessories

FAQ

What is the power output of the Amplifier section?

The power output specification is 60 W + 60 W with THD 0.2%.

What is the input sensitivity for PHONO MM?

The input sensitivity for PHONO MM is 2.8 mV/47 k.

What are the power requirements for the amplifier?

The power requirements are AC 220-230 V, 50/60 Hz.