02Connecting up
Connecting using the component video output
You can use the component video output instead of the standard video out jack to connect this player to your TV (or other equipment).
•Use a component video cable (not supplied) to connect the COMPONENT VIDEO OUT jacks to a component video input on your TV, monitor or AV receiver.
Be careful to match up the colors of the three jacks for correct connection.
|
|
|
| Y |
|
|
|
|
|
|
|
| PB |
|
|
|
|
|
|
|
| PR |
|
|
|
|
|
|
|
| COMPONENT |
|
|
| |
|
|
|
| VIDEO IN |
|
|
| |
TV |
|
|
|
|
|
|
|
|
CONTROL | IN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
IR |
|
|
|
|
|
| AUDIO OUT | AUDIO OUT |
| IN |
| Y |
|
|
| (5.1ch) | (2ch) |
| VIDEO OUT |
|
|
| CENTER | SURROUND | FRONT | |
|
|
|
|
| ||||
|
|
|
|
| AUDIO OUT |
| L | L |
SETTING 2 |
|
| PB |
|
|
|
| |
HDMI OUT | LAN(10/100) |
|
|
|
|
| ||
SETTING 1 |
|
|
|
|
|
|
|
|
IR RECEIVER |
| S | PR |
|
|
|
| R |
|
|
|
|
|
| |||
|
|
| COMPONENT | COAXIAL | OPTICAL | SUB WOOFER | R |
|
|
|
|
|
| ||||
|
|
| VIDEO OUT |
|
|
|
|
|
Changing the output video resolution
Use the OUTPUT RESOLUTION button located on both the front panel and the remote control to switch the output video resolution for the HDMI and component video outputs.
The table below shows the output settings.
Setting | HDMI output | Component | |
|
| output | output |
AUTO | TV’s preferred | TV’s preferred | 480/60i |
| resolution *3,5 | resolution *6 |
|
480i | 480/60i | 480/60i | 480/60i |
|
|
|
|
480p | 480/60p | 480/60p | 480/60i |
|
|
|
|
720p | 720/60p | 720/60p *1,2 | 480/60i |
|
|
|
|
1080i | 1080/60i | 1080/60i *1,2 | 480/60i |
1080p | 1080/60p | 480/60i | 480/60i |
|
|
|
|
Source | Dependent on | Dependent on | 480/60i |
Direct | source *3,5 | source *2,4,5 |
|
*1 Video output is 480i during copy protected
*2 Video output during
*3 Refer to 24p output below for conditions.
*4 The frame frequency for 1080/24p is still 60 Hz.
*5 The video output will be interrupted when switching the video output.
*6 For resolutions that cannot be output by component output, video is output in the following resolutions: 480/60i
14
Note
•Depending on your display, some of the settings may result in the picture disappearing. In this case, press OUTPUT RESOLUTION repeatedly until the picture
•1080/60p and 1080/24p output is only compatible with HDMI displays. They are not compatible with the component video output.
•When Output Video Resolution is set to 720p, 1080i or 1080p, video is output in 16:9 format even if TV Aspect Ratio is set to 4:3 (Standard). See TV Aspect Ratio on page 41.
•If the contours of the displayed subjects look jagged or blurred, try setting the Output Video Resolution to 480i. (If you connected this player to your TV with the HDMI connection and the picture disappears when you switch the Output Video Resolution to 480i, use the component connection with the 480i Output Video Resolution or
•Note that when using a Component Video connection with a TV or other AV component (not using HDMI), 480/60i video may be output in 480/60p.
24p output
For smooth presentation of 1080/24p or 720/24p video with an
This player will output 1080/24p video over HDMI in the following cases:
•1080/24p video: When the Output Video Resolution is set to Auto or Source Direct.
•720/24p video: When the Output Video Resolution is set to Auto.
Note
•Even when 24p Direct Out is set to On, if a TV not compatible with 1080/24p video is connected, the actual frame frequency of the video output will be 60 Hz.
•The video output will be interrupted when switching the video output from 1080/24p or 720/24p to other output video resolutions, or when switching to 1080/24p or 720/24p from other output video resolutions.
En
