Pioneer CLD-V5000 2.3 Function Switches, 2-G, DOWN, Figure, Function, Figure 2-G, Function Switch Settings, Sec. 3.7.6 Register Control Commands, CLD-V5000Level II • Chapter Two

CLD-V5000 Level II • Chapter Two

2.3 Function Switches

The CLD-V5000 videodisc player has eight physical dip-switches on the rear panel of the player (See Figure 2-Gbelow.) The switches are set as follows when the player is shipped from the factory: Switch 1 and 4 are DOWN (ON) and Switch 2, 3, 5, 6, 7and 8 are UP (OFF). These defaults set the player to: 4800 BAUD, 1-Side Repeat ON, Power-on/Load Start OFF, Background Color BLUE, and Sequential Playback OFF. See Sec. 3.7.6 Register Control Commands., page 3-39.

Function Switch Settings

1	2	3	4	5	6	7	8	CLD-V5000 has 8 function switches on the back of
								the player. After changing the switches to new
								settings, power down and then power on the
								player again to commit the settings to the player’s
								memory. Default settings are shown here.

Switch #	Function		DOWN	UP	Factory Setting		Set BAUD Rate w/ SW 1 & 2
Sw 1	BAUD Rate		These two switches are		SW1=DOWN,		BAUD	SW 1		SW 2
		used to set the BAUD RATE:			SW2=UP
							9600	UP		UP
Sw 2	BAUD Rate		9600, 4800, 2400 or 1200		sets 4800 BAUD
							4800	DOWN		UP
Sw 3	1 or 2 side playback		These two switches are		SW 3=UP,		2400	UP		DOWN
					SW 4=DOWN		1200	DOWN		DOWN
			used to set the
					Sets
Sw 4	Repeat 1 or 2 sides		REPEAT MODE
					1-Side Repeat ON	Playback & Repeat w/ SW 3 & 4
Sw 5	Power-On Start		Auto Start	OFF	UP/OFF
						Mode		SW 3		SW 4
Sw 6	Background		Black	Blue	UP/Blue	Stops after one-side
						completes playback			UP		UP
						Stops after both-side
Sw 7	Sequential		ON	OFF	UP/OFF
						complete playback			DOWN		UP
	Playback
						One-side Repeat			UP		DOWN
Sw 8	Not Used		Must be OFF		UP/OFF
						Two-side Repeat			DOWN		DOWN

Figure 2-G

SW1 and SW2: These two switches are used to set the BAUD rate of the Player for RS-232C communications to 9600, 4800, 2400, or 1200 BAUD. The factory set default is 4800 BAUD, with Switch 1 DOWN and Switch 2 UP.

SW3 and SW4: These two switches are used to set the REPEAT MODE of the Player to stop after one side of the disc completes playback, after both sides complete playback, or to allow continuous one-side repeat playback or continuous two-sided repeat playback. The default is One-Side Repeat ON

SW5: Automatic playback begins when a disc is loaded in the tray, the tray table is pushed in and power is turned ON. Default is OFF. UP=OFF. DOWN=ON.

SW6: Background for setting squelch color: Black is DOWN=ON; Blue is UP=OFF. Default is Blue = UP.

SW7: Sequential Playback. Default UP=OFF. To enable sequential playback, Set SW 7 DOWN=ON and use a special RS-232C cable to connect two or more players. With sequential playback enabled, and when playback of a disc completes, the next player immediatly starts playback. See Appendix E for details.

SW8: This switch is NOT USED and must always be UP=OFF.

2-6 TP 121 v. 1.0 • 1/96 CLD-V5000 Level III User’s Manual