When loops are stored in loop slots ahead of time, they can be called out later.
!Up to eight loops can be set in the loop slots.
!When you select the number of the loop slot at which you want to store the loop then set a loop, the loop is automatically stored.
!When a new loop is set after a loop has been stored, the loop is overwritten and the slot is updated.
!When the number of the loop slot whose loop you want to call out is selected and the LOOP OUT button is pressed while pressing the [SHIFT] button (reloop), playback of the stored loop starts.
BLOOP OUT button
Press:
The loop out point is set, and loop playback begins.
When this button is pressed during loop playback, the loop out point can be
[SHIFT] + press:
Cancels loop playback. (Loop Exit)
After loop playback is canceled, playback returns to the previously set loop in point and loop playback resumes. (Reloop)
CHOT CUE mode button
Press:
Sets the hot cue mode.
[SHIFT] + press:
This will be used with future function enhancements of the Serato DJ software.
!For function enhancements, see the Pioneer DJ support site below.
http://pioneerdj.com/support/
DROLL mode button
Press:
Sets the roll mode.
[SHIFT] + press:
This will be used with future function enhancements of the Serato DJ software.
!For function enhancements, see the Pioneer DJ support site below.
http://pioneerdj.com/support/
ESLICER mode button
Press:
Sets the slicer mode.
!The mode switches between slicer mode 1 and slicer mode 2 each time the button is pressed.
!To cancel the slicer mode, press one of the [ROLL] mode, [SAMPLER] mode or [HOT CUE] mode buttons.
[SHIFT] + press:
This will be used with future function enhancements of the Serato DJ software.
!For function enhancements, see the Pioneer DJ support site below.
http://pioneerdj.com/support/
FSAMPLER mode button
Press:
Sets the sampler mode.
Press for over 1 second:
Turns the sampler velocity mode on and off.
!For details on the sampler velocity mode, see Using the sampler velocity mode on page 25.
[SHIFT] + press:
This will be used with future function enhancements of the Serato DJ software.
!For function enhancements, see the Pioneer DJ support site below.
http://pioneerdj.com/support/
GPerformance pads
The performance pads are used to control the hot cue, loop roll, slicer and sampler functions.
=Using the performance pads (p.22)
HPARAMETERcbutton, PARAMETERdbutton
Use these to set the loop roll, slicer and sampler parameters.
=Using the performance pads (p.22)
IPLAY/PAUSE fbutton
Press:
Use this to play/pause tracks.
[SHIFT] + press:
The track returns to the temporary cue point and playback continues from there. (Stutter)
JCUE button
Press:
This is used to set, play and call out temporary cue points.
!When the [CUE] button is pressed while pausing, the temporary cue point is set.
!When the [CUE] button is pressed during playback, the track returns to the temporary cue point and pauses. (Back Cue)
!When the [CUE] button is pressed and held after the track returns to the temporary cue point, playback continues as long as the button is pressed in. (Cue Sampler)
!When the [PLAY/PAUSE f] button is pressed during cue sampling, playback continues from that point.
[SHIFT] + press:
Loads the previous track in the track list. (Previous Track)
!If the current playback position is not the beginning of a track, the track returns to the beginning.
KSYNC button
Press:
The tempos (pitches) and beat grids of tracks on multiple decks can be synchronized automatically.
[SHIFT] + press: Cancels the sync mode.
LSHIFT button
When another button is pressed while pressing the [SHIFT] button, a different function is called out.
MDECK button
Switches the deck to be operated.
NDUAL DECK button
Turns the dual deck mode on and off.
=Using the dual deck mode (p.24)
OGRID ADJUST button
Press:
When the jog dial is turned while pressing the [GRID ADJUST] but- ton, the beat grid interval can be adjusted.
[SHIFT] + press:
Sets a beat marker. (Grid Set)
!Beat markers can be set at multiple points.
PGRID SLIDE button
Press:
When the jog dial is turned while pressing the [GRID SLIDE] button, the overall beat grid can be slid to the left or right.
[SHIFT] + press:
Clears the beat markers. (Grid Clear)
QSLIP button
This turns the slip mode on/off.
=Using the slip mode (p.23)
names part and Connections
En 13