Pioneer DEH-7300BT, DEH-73BT Initial Settings, Operating this unit, Operating this unit

Section
02	Operating this unit

Operating this unit

1	Press M.C. to display the setting mode.			The cut-off frequency and output level can be ad-
1	Press M.C. to display the setting mode.			justed when the subwoofer output is on.
2	Turn M.C. to select the equalizer.			justed when the subwoofer output is on.
2	Turn M.C. to select the equalizer.			Only frequencies lower than those in the selected
	DYNAMIC—VOCAL—NATURAL—CUSTOM			Only frequencies lower than those in the selected
	DYNAMIC—VOCAL—NATURAL—CUSTOM			range are outputted from the subwoofer.
	—FLAT—POWERFUL			range are outputted from the subwoofer.
	—FLAT—POWERFUL	1			Press M.C. to display the setting mode.
3	Press M.C. to confirm the selection.	1			Press M.C. to display the setting mode.
3	Press M.C. to confirm the selection.		2		Press M.C. to cycle between the cut-off fre-

TONE CTRL (equalizer adjustment)
TONE CTRL (equalizer adjustment)					quency and output level of the subwoofer.
!	Adjusted equalizer curve settings are stored in				Cut-off frequency (Cut-off frequency display
!	Adjusted equalizer curve settings are stored in				flashes.)—Output level (Output level display
	CUSTOM.				flashes.)
1	Press M.C. to display the setting mode.	3			Turn M.C. to select the desired setting.
2	Press M.C. to select BASS (bass)/MID (mid)/				Cut-off frequency: 50HZ—63HZ—80HZ—
	TREBLE (treble).				100HZ—125HZ
3	Turn M.C. to adjust the level.				Output level: -24 to +6
	Adjustment range: +6 to -6
	Adjustment range: +6 to -6			SLA (source level adjustment)

LOUDNESS (loudness)
LOUDNESS (loudness)				SLA (Source Level Adjustment) lets you adjust the
Loudness compensates for deficiencies in the low-				SLA (Source Level Adjustment) lets you adjust the
Loudness compensates for deficiencies in the low-				volume level of each source to prevent radical
and high-frequency ranges at low volume.				changes in volume when switching between sour-
1	Press M.C. to display the setting mode.			ces.
2	Turn M.C. to select the desired setting.	!			Settings are based on the FM volume level,
	OFF (off)—LOW(low)—HIGH (high)				which remains unchanged.
3	Press M.C. to confirm the selection.	!			The AM volume level can also be adjusted with
SUBWOOFER1 (subwoofer on/off setting)			!		this function.
SUBWOOFER1 (subwoofer on/off setting)					When selecting FM as the source, you cannot
This unit is equipped with a subwoofer output					When selecting FM as the source, you cannot
This unit is equipped with a subwoofer output					switch to SLA.
which can be turned on or off.		1			Press M.C. to display the setting mode.
1	Press M.C. to display the setting mode.	2			Turn M.C. to adjust the source volume.
2	Turn M.C. to select the desired setting.				Adjustment range: +4 to –4
	NORMAL (normal phase)—REVERSE (reverse	3			Press M.C. to confirm the selection.
	phase)—OFF (subwoofer off)
	phase)—OFF (subwoofer off)

3Press M.C. to confirm the selection.

SUBWOOFER2 (subwoofer adjustment)	Initial Settings
	1	Press and hold S (SRC/OFF) until the unit
	turns off.
	2	Press M.C. and hold until function name
	appears in the display.
	3	Turn M.C. to select the initial setting.
	After selecting, perform the following proce-
	dures to set the initial setting.

CLOCK SET (setting the clock)

1Press M.C. to display the setting mode.

2Press M.C. to select the segment of the clock display you wish to set.

Hour—Minute

3Turn M.C. to adjust the clock.

AUX (auxiliary input)

Activate this setting when using an auxiliary device connected to this unit.

1Press M.C. to turn AUX on or off.

USB (plug and play)

This setting allows you to switch your source to USB/iPod automatically.

1Press M.C. to turn the plug and play function on or off.

ON – When a USB storage device/iPod is con- nected, depending on the type of device, the source is automatically switched to USB/iPod when you turn on the engine. If you disconnect your USB storage device/iPod, this unit’s source is turned off.

OFF – When a USB storage device/iPod is con- nected, the source is not switched to USB/ iPod automatically. Please change the source to USB/iPod manually.

SW CONTROL (rear output and subwoofer set- ting)

The rear speaker leads output and RCA output can be used for full-range speaker or subwoofer connection.

If you switch to REAR-SP:SW, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp.

Initially, REAR-SP is set for rear full-range speaker connection (FUL).

1Press M.C. to display the setting mode.

2Turn M.C. to change the output and press to select.

REAR-SP—PREOUT

3Turn M.C. to change the setting. REAR-SP: FUL—SW PREOUT: SW—REA

!Even if you change this setting, there will be no output unless you turn the sub- woofer output on (refer to SUBWOOFER1 (subwoofer on/off setting) on this page).

!If you change this setting, subwoofer out- put in the audio menu will return to the fac- tory settings.

DEMO (demo display setting)

1Press M.C. to turn the demo display on or off.

SCROLL (scroll mode setting)

When ever scroll is set to ON, recorded text information scrolls continuously in the display. Set to OFF if you prefer the information to scroll just once.

1Press M.C. to turn the ever scroll on or off.

BT CLEAR (resetting the Bluetooth wireless technology module)

10En