Operating this unit
InstallationSection
03
Bluetooth telephone data can be deleted. To protect personal information, we recommend deleting this data before transferring the unit to other per- sons. The following settings will be deleted.
!phone book entries on the Bluetooth tele- phone
!preset numbers on the Bluetooth telephone
!registration assignment of the Bluetooth tele- phone
!call history of the Bluetooth telephone
!information of the connected Bluetooth tele- phone
1Press M.C. to show the confirmation display. YES is displayed. Clearing memory is now on standby.
If you do not want to reset phone memory, press 
. The display reverts.
2Press M.C. to clear the memory.
CLEARED is displayed and the settings are de- leted.
!While this function is in use, do not turn off the engine.
VER INFO (Bluetooth version display)
You can display the system versions of this unit and of Bluetooth module.
1Press M.C. to display the information.
S/W UPDATE (updating the software)
This function is used to update this unit with the latest software. For information on the software and updating, refer to our website.
!Never turn the unit off while the software is being updated.
1Press M.C. to display the data transfer mode. Follow the
1Insert the stereo mini plug into the AUX input jack.
2Press S (SRC/OFF) to select AUX as the source.
Note
AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on the previous page.
Turning the clock display on or off%Press
to turn the clock display on or
off.
# The clock display disappears temporarily when you perform other operations, but the clock display appears again after 25 seconds.
WARNING
!Use speakers over 50 W (output value) and between 4 W to 8 W (impedance value). Do not use 1 W to 3 W speakers for this unit.
!The black cable is ground. When installing this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly con- nected to metal parts of the car’s body. The ground wire of the power amp and the one of this unit or any other device must be con- nected to the car separately with different screws. If the screw for the ground wire loos- ens or falls out, it could result in fire, genera- tion of smoke or malfunction.
Ground wire | POWER AMP | ||
|
|
|
|
|
|
|
|
Other devices | Metal parts of car’s body | |
(Another electronic | ||
| ||
device in the car) |
|
Important
!When installing this unit in a vehicle without an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain.
| F | ON | |
| F |
|
|
| O |
| S |
|
|
| T |
|
| TR | A |
ACC position | No ACC position | ||
!Use this unit with a
!To prevent a
—Disconnect the negative terminal of the bat- tery before installation.
—Secure the wiring with cable clamps or adhe- sive tape. Wrap adhesive tape around wiring that comes into contact with metal parts to protect the wiring.
—Place all cables away from moving parts, such as the gear shift and seat rails.
—Place all cables away from hot places, such as near the heater outlet.
—Do not connect the yellow cable to the battery by passing it through the hole to the engine compartment.
—Cover any disconnected cable connectors with insulating tape.
—Do not shorten any cables.
—Never cut the insulation of the power cable of this unit in order to share the power with other devices. The current capacity of the cable is limited.
—Use a fuse of the rating prescribed.
—Never wire the negative speaker cable directly to ground.
—Never band together negative cables of multi- ple speakers.
!When this unit is on, control signals are sent through the blue/white cable. Connect this cable to the system remote control of an ex- ternal power amp or the vehicle’s
!Never connect the blue/white cable to the power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna. Doing so may result in battery drain or a malfunction.
English
En 11