Pioneer DJM-900SRT, DJM-900SRT Serato DJ Edition Changing the settings, About the auto standby function, About the talk over function, Setting preferences, About the setting utility software

Changing the settings

1 Press the [ON/OFF (UTILITY)] button for over 1 second.

The [USER SETUP] mode setting screen is displayed.

!To display the [CLUB SETUP] mode setting screen, first turn this unit’s power off, then press the [POWER] button while pressing the [ON/OFF (UTILITY)] button.

2 Press the [BEAT c, d] button.

Select the setting item.

3 Press the [TAP] button.

The screen switches to the setting item’s setting value change screen.

4 Press the [BEAT c, d] button.

Change the setting value.

5 Press the [TAP] button.

Enter the setting value.

The previous screen reappears.

!To return to the previous screen without changing the settings, press the [QUANTIZE] button.

6 Press the [ON/OFF (UTILITY)] button.

Close the [USER SETUP] mode setting screen.

!To close the [CLUB SETUP] mode setting screen, press the [POWER] button to turn this unit’s power off.

About the auto standby function

When [Auto Standby] is set to [ON], the standby mode is set automatically if 4 hours pass with all of the conditions shown below met.

—That none of this unit’s buttons or controls are operated.

—That no audio signals of –10 dB or greater are input to this unit’s input terminals.

—That no PRO DJ LINK connections are made.

!When the [LFO FORM (WAKE UP)] button is pressed, the standby mode is canceled.

!This unit is shipped with the auto standby function turned on. If you do not want to use the auto standby function, set [Auto Standby] to [OFF].

About the talk over function

The talk over function has the two modes described below.

—[ADV] (advanced talk over): The mid-range only of the sound of channels other than the [MIC] channel is attenuated according to the [Talk Over LEVEL] setting value and output.

dB

Frequency

— [NOR] (normal talk over): The sound of channels other than the [MIC] channel is attenuated according to the [Talk Over LEVEL] setting value and output.

dB

Frequency

Setting preferences

*: Setting upon purchase
Mode	Options settings	Screen display	Setting value	Descriptions
	Fader Start	F.S.	ON, OFF*	Turns the Fader Start function on and off all at once.
	MIDI CH	MIDI CH	1* to 16	Sets the MIDI channel.
USER SETUP	MIDI Button Type	MIDI BT	TGL*, TRG	Selects the MIDI signal transmission mode, [TGL (TOGGLE)] or [TRG (TRIGGER)].
	Talk Over Mode	TLK MOD	ADV*, NOR	Selects the talk over function’s mode, [ADV(ADVANCED)] or [NOR(NORMAL)].
	Talk Over LEVEL	TLK LVL	–6 dB, –12 dB,	Sets the talk over function’s sound attenuation level.
			–18 dB*, –24 dB
	Digital Master Out	DOUT LV	–19 dB*, –15 dB,	Sets the maximum level of the sound output from the [DIGITAL MASTER OUT] terminals. 1
	Level		–10 dB, –5 dB
	Digital Master Out	DOUT FS	48 kHz, 96 kHz*	Sets the digital signal’s sampling rate.
	Sampling Rate
	MASTER ATT.	MST ATT	–6 dB, –3 dB, 0 dB*	Sets the attenuation level of the sound output from the [MASTER1] and [MASTER2] terminals.
CLUB SETUP	Auto Standby	AUTOSTB	ON*, OFF	Turns the auto standby function on and off.
	Mic Output To Booth	MIC BTH	ON*, OFF	Sets whether or not to output the microphone’s audio signals from [BOOTH] terminals.
	Monitor
	PC UTILITY	PC UTLY	ON, OFF*	Sets whether or not to launch the computer’s setting utility software automatically when a USB cable is
				connected.
	Peak Limiter	PKLIMIT	ON*, OFF	Lessens sudden, unpleasant digital clipping of the master output.
	Factory Reset	INITIAL	YES, NO*	Restores all the settings to their factory defaults.

1Note that the output sound may be distorted even if the master level indicator does not light up to the very top.

About the setting utility software

The setting utility can be used to make the checks and settings described below.

—Checking the status of this unit’s input selector switches

—Setting the audio data output from this unit to the computer

—Adjusting the buffer size (when using Windows ASIO)

—Checking the version of the driver software

Displaying the setting utility

For Windows

Click [Start] menu > [All Programs] > [Pioneer] > [DJM-900SRT] > [DJM-900SRT Settings Utility].

For Mac OS X

Click [Macintosh HD] icon > [Application] > [Pioneer] > [DJM-900SRT] > [DJM- 900SRT Settings Utility].

Checking the status of this unit’s input selector switches

Display the setting utility before starting.

24En