Pioneer PRO 910HD, PRO 1110HD manual Appendix, Troubleshooting

14	Appendix
	Troubleshooting
	Problem	Possible Solution
	• No power.	• Make sure the Plasma Display and the Media Receiver are connected correctly. (See page 20.)
		• Is the power cord disconnected? (See page 27.)
		• Has the main power been turned on? (See page 28.)
		• Check if you pressed TV a on the remote control unit. (See page 28.)
		If the indicator on the system lights up red, press TV a.
	• Green and red rectangles appear on	• Check if the system cable has been disconnected or almost disconnected? (See page 20.)
	the screen alternately.
	• The system cannot be operated.	• External influences such as lightning, static electricity, etc., may cause improper operation.
		In this case, operate the system after first turning the power of the Plasma Display and the
		Media Receiver, or unplugging the power cord and re-plugging it in after 1 or 2 minutes.

•Remote control unit does not operate.

•Is the Mode switch set correctly? Slide it to the TV setting position. (See page 16.)

•Are batteries inserted with polarity (+, –) aligned? (See page 22.)

•Are batteries worn out? (Replace with new batteries.) (See page 22.)

•Operate the remote control unit while pointing it toward the remote control sensor on the Plasma Display. (See page 17.)

•Are you using it under strong or fluorescent lighting?

•Is a fluorescent light illuminated near the remote control sensor?

• No image and audio is presented.	• Check if the input source for video or PC has been unintentionally selected although you want
	to watch a TV channel. (See page 30.)
	• Check if you have activated the Parental Control function. (See page 90.)
	Enter a password to temporarily cancel the Parental Control function. (See page 94.)
• No picture.	• Is connection to other components correct? (See pages 65 to 77.)
	• Is a non-compatible PC signal being input? (See page 107.)
	• Is picture adjustment correct? (See pages 47 to 53.)

•Images are presented but no audio is output.

•Check if you have selected the minimum volume. (See page 31.)

•Check if you have muted sound. (See page 31.)

•When using a video or PC input source, check that the audio terminal is also in connection. (See pages 65 to 70 and 77.)

• Sound is reversed between the right	• Check if the speaker cable connections have been reversed between the right and left or if the
and left.	speaker cable from either speaker has been disconnected. (See pages 13 and 20.)
• Sound is output from only a single	• Has the balance been correctly adjusted? (See page 53.)
speaker.
• Picture is cut off.	• Is the image position correct? (See pages 81and 82.)
	• Has the correct screen size been selected? (See page 83.)
• Strange colour, light colour, dark or	• Adjust the picture tone. (See pages 47 to 53.)
colour misalignment.	• Is the room too bright? The picture may look dark in a room that is too bright.
• Power is suddenly turned off.	• Is the sleep timer set? (See page 85.)
	• Check the power control setting. (See pages 55 and 56.)
	• The system’s internal temperature has increased. Remove any objects blocking vent or clean.
	(See pages 18 to 19.)

Code Message

SD04 Powering off. Internal temperature too high. Check temperature around PDP.

Check

Check if the ambient temperature of the Plasma Display is high.

SD05	Powering off. Internal protection circuits activated,	Check the speaker cable connections between the Plasma Display
	Is there a short in speaker cable?	and the speakers.
SD11	Powering off. Internal temperature too high.	Check if the ambient temperature of the Plasma Display and the
	Check temperature around media receiver.	Media Receiver is high.

106

En

PDP-ELITE-Eng (106-111) 106 9/9/03, 11:43