08Other connections
• Password Set – Set the parental lock password.
3When you’re finished press TOP MENU to return to the reception display.
Connecting the multichannel analog inputs
For DVD Audio and SACD playback, your DVD player may have 5.1, 6.1 or 7.1 channel analog outputs (depending on whether your player supports surround back
channels).1 Make sure that the player is set to output multichannel analog audio.
1Connect the front, surround, center and subwoofer outputs on your DVD player to the corresponding MULTI CH input jack on this receiver.
•Use standard RCA/phono jack cables for the connections.
2If your DVD player also has outputs for surround back channels, connect these to the corresponding MULTI CH input jacks on this receiver.
•Use standard RCA/phono jack cables for the connections.
•If there is a single surround back output, connect it to the SURROUND BACK L (Single) jack on this receiver.
Selecting the multichannel analog inputs
If you have connected a decoder or a DVD player as above, you must select the analog multichannel inputs
for surround sound playback.2
Speaker B setup
Caution
•Before making or changing the connections, switch off the power and disconnect the power cord from the power outlet. Plugging in components should be the last connection you make with your system.
•Be careful not to allow any contact between speaker wires from different terminals.
•You can use speakers with a nominal impedance between 6 Ω to 16 Ω (please see Switching the
speaker impedance on page 60 if you plan to use speakers with an impedance of less than 8 Ω).
After selecting Speaker B in Surround back speaker setting on page 35, you can use the speakers connected to the (surround back) B speaker terminals on the rear panel to listen to stereo playback in another room. See Switching the speaker system below for the listening options with this setup.
1Connect a pair of speakers to the surround back speaker terminals on the rear panel.
Connect them the same way you connected your speakers in Installing your speaker system on page 18. Make sure to review Placing the speakers on page 19 when placing the speakers in another room.
2Select ‘Speaker B’ from the ‘Surr Back System’ menu.
See Surround back speaker setting on page 35 to do this.
1Make sure you have set the playback source to the proper output setting.
For example, you might need to set your DVD player to output multichannel analog audio.
2Press MULTI CH IN (front panel).
•Depending on the DVD player you’re using, the analog output level of the subwoofer channel may be too low. In this case switch the receiver into standby, then press STANDBY/ON while holding down SBch PROCESSING on the front panel. This switches between SW IN +10dB (increase of 10 decibels) and SW IN 0dB (default) in the subwoofer channel.
Switching the speaker system
If you selected Speaker B in Surround back speaker setting on page 35, three speaker system settings are possible using the SPEAKERS button. If you selected Normal (SB) or Front
below are for the Speaker B setting only.3
•Use the SPEAKERS button on the front panel to select a speaker system setting.
As mentioned above, if you have selected Normal (SB), the button will simply switch your main speaker system
(A) on or off.
Press repeatedly to choose a speaker system option:
•SPA – Sound is output from speaker system A and the same signal is output from the
Note
1To listen to multichannel analog audio you’ll need to select MULTI CH IN (see Selecting the multichannel analog inputs above for more on this).
2• When playback from the multichannel inputs is selected, you can’t use the sound processing features, SIGNAL SELECT, or any of the listening modes (including STEREO and the surround back channel processing).
•When playback from the multichannel inputs is selected, only the volume and channel levels can be set.
•You can’t listen to your speaker B system during playback from the multichannel inputs.
3• The subwoofer output depends on the settings you made in Manual speaker setup on page 40. However, if SPB is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed).
•Depending on the settings in Surround back speaker setting on page 35 output from the surround back
•All speaker systems (except Speaker B connections) are switched off when headphones are connected.
48
En
