Controlling the rest of your system | 11 |
8Repeat steps
9When you’re finished, use / to select EDITEXIT from the menu and press ENTER.
You will return to the remote control SETUP menu. Select * EXIT * again to exit.
Using multi operations
You can start multi operations with the receiver switched on, or in standby.
AUDIO | SUBTITLE | HDD | DVD | |
DISP |
| CH | CH | |
| PHOTO | STEREO/ | ||
THX | STANDARD | ADV.SURR | ||
F.S.SURR | ||||
MULTI OPE AUTOSURR ACOUSTIC EQ SIGNAL SEL
SHIFT EFFECT/CHSEL | LEVEL |
RECEIVER
1 Press MULTI OPE.
MULTI OP flashes in the display.
2Press an input source button that has been set up with a multi operation.
The receiver switches on (if it was in standby) and the programmed multi operation is performed automatically.
Using System off
|
|
| AUDIO | SUBTITLE | HDD |
| DVD |
|
| SYSTEM OFF | DISP |
| CH |
| CH |
RECEIVER | INPUT |
| PHOTO |
|
| ||
SOURCE | THX | STANDARD | ADV.SURR | STEREO/ | |||
| SELECT |
| F.S.SURR | ||||
|
|
| MULTI OPE | AUTOSURR | ACOUSTIC EQ | SIGNAL SEL | |
|
|
| SHIFT | EFFECT/CHSEL | LEVEL | ||
XM RADIO | SIRIUS | DVR 2 |
| RECEIVER |
|
| |
DVD | TV | DVR 1 TVCTRL |
|
|
| ||
|
|
|
|
| |||
1 Press MULTI OPE.
MULTI OP flashes in the display.
2 Press SOURCE.
The command sequence you programmed will run, then
all Pioneer components will switch off1, followed by this receiver.
Controls for TVs
This remote control can control components after entering the proper codes or teaching the receiver the commands (see Setting the remote to control other components on page 61 for more on this). Use the input source buttons to select the component.
•The TV CONTROL buttons on the remote control are dedicated to control the TV assigned to the TV CTRL button. If you have two TVs, assign the main TV to the TV CTRL button.
Button(s) | Function | Components |
TV | Press to switch the component | Cable TV/Satellite |
| assigned to the TV CONT | TV/TV/DTV |
| button on or off. |
|
|
|
|
INPUT | Switches the TV input. (Not | Cable TV/Satellite |
SELECT | possible with all models.) | TV/TV/DTV |
|
|
|
TV CH +/– | Selects channels. | Cable TV/Satellite |
|
| TV/TV/DTV |
|
|
|
TV VOL +/– | Adjust the TV volume. | Cable TV/Satellite |
|
| TV/TV/DTV |
|
|
|
SOURCE | Switches the DTV on or off. | DTV |
|
|
|
| Switches the TV or CATV between | Cable TV/Satellite |
| standby and on. | TV/TV |
|
|
|
| Switches the DTV on or off. | DTV |
|
|
|
| Press to get information on DTV | DTV |
| programs. |
|
|
|
|
| Use to choose the BLUE | DTV |
| commands on a DTV menu. |
|
|
|
|
| Use to choose the YELLOW | DTV |
| commands on a DTV menu. |
|
|
|
|
| Use to choose the GREEN | DTV |
| commands on a DTV menu. |
|
|
|
|
| Use to choose the RED | DTV |
| commands on a DTV menu. |
|
|
|
|
AUDIO / DISP | Use to switch DTV audio tracks. | DTV |
|
|
|
SUBTITLE | Use to return to the previously | Cable TV/Satellite |
| selected channel. | TV/TV/DTV |
|
|
|
GUIDE | Use as the GUIDE button for | Cable TV/Satellite |
| navigating. | TV/TV/DTV |
|
|
|
ANT | Use to select the VHF/UHF | Cable TV/TV |
| antennas or Cable TV. |
|
|
|
|
RETURN | Use to select RETURN or EXIT. | DTV |
|
|
|
Number | Use to select a specific TV | Cable TV/Satellite |
buttons | channel. | TV/TV/DTV |
|
|
|
+10 button | Use to add a decimal point when | DTV |
| selecting a specific TV channel. |
|
|
|
|
ENTER/ | Use to enter a channel. | Cable TV/Satellite |
DISC |
| TV/TV/DTV |
|
|
|
MENU | Select different menus from the | DTV |
| DTV functions. |
|
|
|
|
| Select the menu screen. | Cable TV/Satellite |
|
| TV/TV |
|
| |
/// Press to select or adjust and | Cable TV/Satellite | |
& ENTER | navigate items on the menu | TV/TV/DTV |
| screen. |
|
|
|
|
Note
1 In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
63
En
