The System Setup menu | 0606 |
5Adjust the level of each channel using /.
If you selected Manual, use / to switch speakers. The Auto setup will output test tones in the order shown on- screen:
2c.Channel Level |
|
|
|
|
|
Front L |
| 0dB |
Center | [ | 0dB] |
Front R | [ | 0dB] |
Surround R | [ | 0dB] |
Surr. Back R | [ | |
Surr. Back L | [ | |
Surround L | [ | 0dB] |
Subwoofer | [ | 0dB] |
Speaker Distance
For good sound depth and separation from your system, you need to specify the distance of your speakers from the listening position. The receiver can then add the proper delay needed for effective surround sound.
1Select ‘Manual SP Setup’ from the System Setup menu.
2Select ‘Speaker Distance’ from the Manual SP Setup menu.
If you didn’t make component video connections according |
| English | |||
to the defaults above, you must assign the numbered input to |
| ||||
the component you’ve connected (or else you may see the |
| ||||
video signal of a different component). For more on this, see |
| ||||
Using the component video jacks on page 19. |
|
| |||
|
| ||||
1 Select ‘Input Assign’ from the System Setup menu. |
| ||||
Español | |||||
System Setup | |||||
| 1.Auto MCACC | ||||
| 2.Manual SP Setup | ||||
|
| ||||
| 3.Input Assign |
|
| ||
| 4.Speaker System |
|
| ||
Return
Adjust the level of each speaker as the test tone is emitted.
Note
• If you are using a Sound Pressure Level (SPL) meter, take |
the readings from your main listening position and adjust |
the level of each speaker to 75 dB SPL |
2.Manual SP Setup
a.Speaker Setting b.Crossover Network c.Channel Level d.Speaker Distance
Return
2d.Speaker Distance |
|
|
| ||
|
|
|
|
|
|
Front L |
|
| 10.0 | ft |
|
Center | [ |
| 10.0 | ft | ] |
Front R | [ |
| 10.0 | tt | ] |
Surround R | [ |
| 10.0 | ft | ] |
Surr. Back R | [ |
| ] | ||
Surr. Back L | [ |
| ] | ||
Surround L | [ |
| 10.0 | ft | ] |
Subwoofer | [ |
| 10.0 | ft | ] |
Return
5.Video Parameter |
6.HDMI Setup |
7.Auto Power Down |
8.FL Demo Mode |
Return |
2Select ‘Component Input’ from the Input Assign menu.
3.Input Assign | 3a.Component Input |
reading). |
• The subwoofer test tone is output at low volumes. You |
may need to adjust the level after testing with an actual |
soundtrack. |
6When you’re finished, press RETURN. You return to the Manual SP Setup menu.
Tip
• You can change the channel levels at any time by press RECEIVER , then press CH SELECT and LEV +/– on the
remote control. You can also press CH SELECT and use / to select the channel, and then use / to adjust the channel levels.
3Adjust the distance of each speaker using /. You can adjust the distance of each speaker in 0.1 feet increments.
4When you’re finished, press RETURN.
You return to the Manual SP Setup menu.
The Input Assign menu
You only need to make settings in the Input Assign menu if you didn’t hook up your equipment according to the default settings for the component video inputs.
•Default settings:
-
-
Important
•If you connect any source component to the receiver using a component video input, you should have your TV connected to this receiver’s COMPONENT VIDEO MONITOR OUT or HDMI OUT output (down converting component video is not possible after assigning an input).
a.Component Input | DVD |
| |
| [ DVR | ] | |
| Return |
| Return |
3Select the number of the component video input to which you’ve connected your video component.
The numbers correspond with the numbers beside the inputs on the rear of the receiver.
4Select the component that corresponds with the one you connected to that input.
Select between BD, DVD, TV (TV/SAT), DVR (DVR/BDR) or OFF.
•Use / and ENTER to do this.
•If you assign a component input to a certain function, any component inputs previously assigned to that function will automatically be switched off.
•Make sure you have connected the audio from the component to the corresponding inputs on the rear of the receiver.
5When you’re finished, press RETURN.
You return to the Input Assign menu.
• For the assignment of the digital signal inputs, see Selecting the audio input signal on page 25.
39
En