09Additional information

Chapter 9:

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Take a look at the other components and electrical appliances being used, because sometimes the problem may lie there. If the trouble isn’t sorted out even after going through the checks below, ask your nearest Pioneer authorized independent service company to carry out repair work.

•If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.

General

The power does not turn on.

Disconnect the power plug from the outlet, and insert again.

Make sure there are no loose strands of speaker wire touching the rear panel. This could cause the receiver to shut off automatically.

The receiver suddenly switches off.

When the Auto Power Down function is working, the power will automatically turn off if the receiver has not operated for several hours. Check the setting for the Auto Power Down function (see The Auto Power Down menu on page 41).

After about a minute (you won’t be able to switch the unit on during this time), switch the receiver back on. If the message persists, call a Pioneer authorized independent service company.

The power suddenly turns on or off, or the input suddenly changes (When the Control with HDMI is ON).

This happens because of the synchronized operation due to the Control with HDMI function. If synchronized operations are not needed, set the Control with HDMI to OFF (see HDMI Setup on page 42).

OVERHEAT shows in the display and the power turns off.

The temperature within the unit has exceeded the allowable value. Try moving the unit for better ventilation (see page 2).

Lower the volume level.

TEMP shows in the display and the volume level drops.

The temperature within the unit has exceeded the allowable value. Try moving the unit for better ventilation (see page 2).

Lower the volume level.

No sound is output when an input function is selected.

Use MASTER VOLUME to turn up the volume.

Press MUTE on the remote control to turn muting off.

Press SPEAKERS to select the proper speaker set (see Switching the speaker terminal on page 12).

Set the SIGNAL SEL to H (HDMI), C1/O1/O2 (digital) or A (analog) according to the type of connections made (refer to page 25).

Make sure the component is connected correctly (refer to Connecting your equipment on page 10).

Check the audio output settings of the source component.

Refer to the instruction manual supplied with the source component.

No image is output when an input function is selected.

Make sure the component is connected correctly (refer to Connecting your equipment on page 10).

Check The Input Assign menu on page 39 to make sure you’re assigned the correct input.

The video input selected on the TV monitor is incorrect. Refer to the instruction manual supplied with the TV.

For HDMI, or when Video Converter is set to OFF and a TV and another component are connected with different cords (in Video Converter on page 40), you must connect your TV to this receiver using the same type of video cable as you used to connect your video component.

Some components (such as video game units) have resolutions that may not be converted. If adjusting this receiver’s Resolution setting (in Resolution on page 40) and/or the resolution settings on your component or display doesn’t work, try switching Video Converter (in Video Converter on page 40) OFF.

No sound from subwoofer.

Make sure the subwoofer is switched on.

If the subwoofer has a volume knob, make sure it’s turned up.

The Dolby Digital or DTS source you are listening to may not have an LFE channel.

Switch the subwoofer setting in Speaker Setting on page 37 to YES or PLUS.

Switch the LFE ATT (LFE Attenuate) on page 35 to LFEATT 0 or LFEATT 5.

No sound from surround or center speakers.

Connect the speakers properly (refer to page 12).

Refer to Speaker Setting on page 37 to check the speaker settings.

Refer to Channel Level on page 38 to check the speaker levels.

The Phase Control feature doesn’t seem to have an audible effect.

If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or depending on the subwoofer, the setting where you think it has the best overall effect on the sound).

Make sure the speaker distance setting is correct for all speakers (see Speaker Distance on page 39).

Considerable noise in radio broadcasts.

Connect the antenna (page 20) and adjust the position for best reception.

Route any loose cables away from the antenna terminals and wires.

Fully extend the FM wire antenna, position for best reception, and secure to a wall (or connect an outdoor FM antenna).

Connect an additional internal or external AM antenna (page 21).

Turn off equipment causing interference or move it away from the receiver (or move antennas farther away from equipment causing noise).

Broadcast stations cannot be selected automatically.

Connect an outdoor antenna (refer to page 21).

Noise during playback of a cassette deck.

Move the cassette deck away from your receiver, until the noise disappears.

48

En