List of WLAN SETTING items
When [MODE] at [WLAN SETTING] is set to [OFF], only [MODE] and [RESET TO DEFAULT] are displayed.
Setting item 1 | Setting item 2 | Setting ranges | Description | |
MODE | — | OFF/ACCESS POINT(AP)*/ | Used to set this unit’s operation mode. | |
WLAN CLIENT | ||||
|
|
| ||
INPUT WPS PINCODE 1 | — | 0 to 9 (max. 8 characters) | When in the access point mode, input the PIN code of the sub unit | |
|
|
| to be connected to this unit here to authorize connection. | |
| SSID | A to Z, a to z, 0 to 9, symbols | Used to set this unit’s [SSID]. | |
| (max. 32 characters) | |||
|
|
| ||
NETWORK SETTING 1 | SECURITY | OPEN / WPA / WPA2 | Used to set this unit’s security (encryption) type. | |
| PASSWORD | A to Z, a to z, 0 to 9, symbols | Used to set this unit’s password. | |
| (max. 64 characters) | |||
|
|
| ||
|
|
|
| |
| IP ADDRESS |
| Sets this unit’s IP address. | |
|
|
|
| |
| SUBNET MASK |
| Sets this unit’s subnet mask. | |
|
|
|
| |
|
|
| This unit uses the 2.4 GHz band. If there is a wireless LAN network | |
|
|
| on the same band in the area and the waves cause interference, | |
| CHANNEL NO. | CH1～AUTO* | making connections and communications instable, try changing | |
|
|
| the channel manually. (By default, this is set to [AUTO] and a | |
|
|
| relatively free channel is selected automatically.） | |
|
|
|
| |
OTHERS 1 |
|
| Used to set whether or not to enable this unit’s DHCP server | |
DHCP SERVER | ENABLE*/DISABLE | function. | ||
| [ENABLE]: Enables the DHCP server function. | |||
|
|
| ||
|
|
| [DISABLE]: Disables the DHCP server function. | |
|
|
|
| |
|
|
| Used to set the frequency band’s width. | |
| CHANNEL WIDTH | 20 MHz*/40 MHz | Only set [40 MHz] when communications are possible by | |
|
|
| IEEE802.11n. Otherwise leave this at [20 MHz]. | |
|
|
|
| |
|
|
| When [WPA] or [WPA2] is set at [SECURITY] under [NETWORK | |
| KEY RENEWAL INTERVAL | 0minute to 60minute* to | SETTING], the encryption key’s renewal interval can be set. | |
| 1440minute | When this setting is made, the encryption key is renewed automati- | ||
|
| |||
|
|
| cally at specific intervals, maintaining a more secure status. | |
|
|
|
| |
RESET TO DEFAULT | — | YES/NO* | Resets the settings at [WLAN SETTING] to the factory defaults. | |
SELECT SSID 2 | — | Method of selection + input | Displays up to 10 receivable networks (SSIDs) in the area. “OTHER” | |
|
| method | at the bottom is used to specify an [SSID] that is not displayed. | |
|
|
| Used to select whether to acquire the network settings automati- | |
DHCP CLIENT 2 |
|
| cally using the DHCP function on the connected network side or to | |
— | ENABLE*/DISABLE | set them manually. | ||
|
|
| [ENABLE]: Acquire the IP address, subnet mask, etc., automatically. | |
|
|
| [DISABLE]: Input the IP address, subnet mask, etc., manually. |
000:000:000:000 to
IP ADDRESS/SUBNET MASK —255:255:255:255
(Set to 192:168:1:1/255:255:255:0 upon purchase.)
When in the access point mode, the fixed values below are set. IP address: 192.168.1.1
Subnet mask: 255.255.255.0
When [DHCP CLIENT] is set to [DISABLE], the values must be input manually.
*: Setting upon purchase
1Not displayed in the WLAN client mode.
2Items marked “**” are not displayed in the access point (AP) mode.
28En