Additional information

Troubleshooting

!Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified after checking the items below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

!This unit may not operate properly due to static electricity or other external influences. In this case, proper operation may be restored by turning the power off, waiting 1 minute, then turning the power back on.

Power supply

Problem

Check

Remedy

The power is not turned on.

Is the power cord properly connected?

Plug in the power cord to an AC outlet. (page 10)

None of the indicators light.

 

 

Is the [STANDBY/ON] switch for power supply

Set the [STANDBY/ON] switch for power supply to [ON]. (page 15)

 

 

set to [ON]?

 

 

 

 

The [STANDBY/ON] indicator flashes

—

Normal operation can sometimes be restored by unplugging the power cord,

and the power does not turn on.

 

waiting at least 1 minute, then plugging the power cord back in.

 

 

If the symptom persists, unplug the power cord and request repairs.

 

 

 

Audio output

Problem

Check

Remedy

No sound or small sound.

Are the [DECK1, PHONO1/LINE1] and [DECK2,

Switch the channel’s input source using the [DECK1, PHONO1/LINE1] and

 

PHONO2/LINE2] selector switches set to the

[DECK2, PHONO2/LINE2] selector switches. (Page 23)

 

proper positions?

 

 

Are the [TRIM] control, channel faders, crossfader

Set the [TRIM] control, channel faders, crossfader and [MASTER LEVEL] control

 

and [MASTER LEVEL] control set to the proper

to the proper positions. (Page 23)

 

positions?

 

 

Is the [LINE, PHONO] selector switch on this

Properly set the [LINE, PHONO] selector switch on this unit’s rear panel accord-

 

unit’s rear panel properly set?

ing to the connected device. (page 10)

Distorted sound.

Is the [MASTER LEVEL] control set to the proper

Adjust [MASTER LEVEL] so that the orange indicator on the master level indica-

 

position?

tor lights at the peak level. (Page 23)

 

Is the [TRIM] control set to the proper position?

Adjust [TRIM] so that the orange indicator on the channel level indicator lights

 

 

at the peak level. (Page 23)

 

Is the [LINE, PHONO] selector switch on this

Properly set the [LINE, PHONO] selector switch on this unit’s rear panel accord-

 

unit’s rear panel properly set?

ing to the connected device. (page 10)

 

 

 

 

Is the sound level input to the [MIC] terminal set to

Set the audio level input to the terminals to a suitable level for the connected

 

an appropriate level?

devices.

 

 

 

No sound is produced, or sound is

Is this unit placed near a TV?

Turn the TV’s power off or install this unit and TV away from each other.

distorted or noisy.

 

 

 

 

 

Microphone sound is not output or

Are the [MIC ATT.] and [MIC LEVEL] controls set

Set the [MIC ATT.] and [MIC LEVEL] controls to the proper positions.

volume is low.

to the proper positions?

 

 

 

 

Sound is distorted when an analog

Have you connected an analog player with a built-

For analog players with built-in phono equalizers, use with the [LINE, PHONO]

player is connected to this unit’s

in phono equalizer?

selector switch on this unit’s rear panel switched to [LINE]. (page 10)

[PHONO/LINE] terminals.

 

 

 

If the analog player with built-in phono equalizer has a PHONO/LINE selector

Or, lighting of the channel level

 

 

switch, switch it to PHONO.

indicator does not change even when

 

 

 

Is an audio interface for computers connected

If the output of the audio interface for computers is line level, use with the [LINE,

the [TRIM] control is turned.

between the analog player and this unit?

PHONO] selector switch on this unit’s rear panel switched to [LINE]. (page 10)

 

 

 

If the analog player has a PHONO/LINE selector switch, switch it to PHONO.

 

 

 

Display

Problem

Check

Remedy

The playing address display is not

—

When playing files recorded in VBR, it may happen that the set cannot detect the

displayed in the remaining time mode.

 

length of the track immediately and that some time is required for the playing

 

 

address display to appear.

The category is not displayed.

Is the rekordbox (Mac/Windows) library informa-

Use a device onto which the library information has been exported from rekord-

 

tion stored on the USB device?

box (Mac/Windows).

 

 

 

 

Is the USB device write-protected?

Cancel the USB device’s write-protection so that this unit can write on it.

 

 

 

Caching meter is not displayed.

Are you playing a track from a USB device?

The caching meter is not displayed when playing tracks from USB devices.

 

Is a track over 10 minutes in length loaded?

The caching meter is not displayed when tracks over 10 minutes in length are

 

 

loaded.

 

 

 

 

Is a WAV file loaded?

—

 

 

 

Nothing is displayed.

Is the auto standby function activated?

This unit is shipped with the auto standby function turned on. If you do not want

 

 

to use the auto standby function, set [AUTO STANDBY] to [OFF]. (page 27)

information Additional

En 33