Manuals / Brands / TV and Video / TV Converter Box / Planet Technology / TV and Video / TV Converter Box

Planet Technology 2.2 Install the Converter, 2.2.1 Stand-aloneInstallation, Step, Step, Step, Step, Step

Models: GT-902 GT-902S GT-905A GT-906A15 GT-906A60 GT-906B15 GT-906B60

1 62

Download 62 pages, 5.52 Mb

2.2 Install the Converter

This section describes how to install your Managed Media Converter and make connections to the Managed Media Converter. Please read the following topics and perform the procedures in the order being presented. The hardware installation of Managed Media Converter do not need software configuration. To install your Managed Media Converter on a desktop or shelf, simply complete the following steps.

2.2.1 Stand-alone Installation

To install a Managed Media Converter stand-alone, on a desktop or shelf, simply complete the following steps:

Step 1: Turn off the power of the device/station in a network to which the Managed Media Converter will be attached.

Step 2: Ensure that there is no activity in the network.

Step 3: Attach fiber cable from the Managed Media Converter to the fiber network. TX, RX must be paired at both ends.

Step 4: Connect the 5VDC power adapter to the Managed Media Converter and verify that the Power LED lights up.

Step 5: Turn on the power of the device/station; the PWR LEDs should light when all cables are attached.

-8-

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning WEEE Warning TABLE OF CONTENTS 1. INTRODUCTION 3. MEDIA CONVERTER MANAGEMENT 5. TROUBLESHOOTING APPENDIX A NETWORKING CONNECTION 1. INTRODUCTION 1.1 Package Contents 1.2 How to Use This Manual 1.3 About the Managed Media Converter ■Application Fiber-opticNetworking for ISP, enterprise, and home 1.4Product Features 1.5PRODUCT SPECIFICATION Power Consumption Power Input Dimensions Operator Environment Storage Environment 2. HARDWARE DESCRIPTION 2.1 GT-90XFront Panel 2.1.1 LED Indicators 2.1.2GT-90XRear Panel 2.2 Install the Converter 2.2.1 Stand-aloneInstallation „GT-905AInstallation Stand-alone Installation 2.2.2 Chassis Installation and Rack Mounting Page 3. MEDIA CONVERTER MANAGEMENT 3.1 Overview 3.2 Management Methods 3.2.1 Web Management 3.2.2 SNMP Management 3.2.3 PLANET Smart Discovery Utility 3.2.4Login the Managed Media Converter 4. WEB MANAGEMENT 4.1 Main Menu 4.2 System 4.2.1 System Information 4.2.2 IP Configuration 4.2.3 Password Setting 4.2.4 Firmware Upgrade “Browser” “Upgrade” “here” Page 4.2.5 SNMP Management SNMP Trap SNMP Trap Destination Cold Start Trap Event Warm Start 4.2.6 Factory Default 4.2.7 System Reboot Page 4.3 Port Management 4.3.1 Port Configuration Flow Control Disable Enable Ingress Rate Limit • No Limit Page 4.3.2 Port Status 4.3.3 Port Statistics 4.4 Converter Configuration 4.5 VLAN 802.1Q Tag Adding an IEEE802.1Q Tag Port VLAN ID 4.5.1 VLAN Group VLAN Mode Management VLAN Group VLAN1 VLAN Group VID 4.5.2 VLAN Per Port Setting 4.5.3 Q-in-QVLAN Setting 4.6 Quality of Service Qos Mode 802.1p Tag Priority IP Address Priority IP DSCP Priority Scheduling Page 4.7 OAM Setup 4.7.1 Local TS-1000OAM Setup 4.7.2 Remote TS-1000OAM Setup Page 4.7.3 TS-1000Loop Back Test TS-1000Loop Back Test Send Packet Number TS-1000Loop Back Test Result Result Result counter 4.7.4 802.3ah Setup 4.7.5802.3ah Loop Back Test 802.3ah Loop Back Test Packet Length (Not include CRC) 802.3ah Loop Back Test Result 4.8 Security 4.9 Logout 5. TROUBLESHOOTING The Link LED is not lit Performance is bad 10/100/1000Base-Tport link LED is lit, but the traffic is irregular Reset APPENDIX A NETWORKING CONNECTION A.1 Device‘s RJ-45Pin Assignments A.2 RJ-45cable pin assignment A.3 Fiber Optical Cable Connection Parameter Standard Fiber Diameter (micron) Modal Bandwidth A.4 Power Information A.5 Available Modules 2080-AA3450-002 EC Declaration of Conformity GT-90xynn : Planet Technology Corp Taiwan PLANET TECHNOLOGY CORPORATION