Planet Technology GT-902, GT-902S, GT-905A, GT-906A15, GT-906A60, GT-906B15, GT-906B60 Step, Step, Step, Stand-alone, Installation, „GT-905AInstallation

#Notice: Please refers to APPENDIX-A for detailed wiring information of the Managed Media Converter. To prevent from optic acceptor malfunction, check the both wires / transmitter before power on the

converter.

GT-905A Installation

GT-905A is with high reliability and flexibility to extend the distance from 220m to 120Km. It depends on the Gigabit mini GBIC modules. The SFP transceivers are hot-plug and hot-swappable. You can plug-in and out the transceiver to/from any SFP port without having to power down the converter.

To install GT-905A with 1000Base-SX / LX SFP, simply complete the following steps:

Step 1: Precede with the steps 4 and steps 5 of session 2.2.1 Stand-alone Installation to connect the network cabling and supply power to your converter.

Step 2: Slot in the 1000Base-SX / LX SFP. Make sure both side of the SFP transceiver are with the same media type, for example: 1000Base-SX / 220m & 550m to 1000Base-SX / 220m & 550m, 1000Base-LX / 10km to 1000Base-LX / 10km

Step 3: Connect the fiber cable. Attach the duplex LC connector on the network cable into the SFP transceiver.

#It recommends using PLANET MGB series 1000Base-SX / LX / LX WDM SFP on the GT-905A. If

Notice: you insert a SFP transceiver that is not supported, the GT-905A will not recognize it.

-9-

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning WEEE Warning TABLE OF CONTENTS 1. INTRODUCTION 3. MEDIA CONVERTER MANAGEMENT 5. TROUBLESHOOTING APPENDIX A NETWORKING CONNECTION 1. INTRODUCTION 1.1 Package Contents 1.2 How to Use This Manual 1.3 About the Managed Media Converter ■Application Fiber-opticNetworking for ISP, enterprise, and home 1.4Product Features 1.5PRODUCT SPECIFICATION Power Consumption Power Input Dimensions Operator Environment Storage Environment 2. HARDWARE DESCRIPTION 2.1 GT-90XFront Panel 2.1.1 LED Indicators 2.1.2GT-90XRear Panel 2.2 Install the Converter 2.2.1 Stand-aloneInstallation „GT-905AInstallation Stand-alone Installation 2.2.2 Chassis Installation and Rack Mounting Page 3. MEDIA CONVERTER MANAGEMENT 3.1 Overview 3.2 Management Methods 3.2.1 Web Management 3.2.2 SNMP Management 3.2.3 PLANET Smart Discovery Utility 3.2.4Login the Managed Media Converter 4. WEB MANAGEMENT 4.1 Main Menu 4.2 System 4.2.1 System Information 4.2.2 IP Configuration 4.2.3 Password Setting 4.2.4 Firmware Upgrade “Browser” “Upgrade” “here” Page 4.2.5 SNMP Management SNMP Trap SNMP Trap Destination Cold Start Trap Event Warm Start 4.2.6 Factory Default 4.2.7 System Reboot Page 4.3 Port Management 4.3.1 Port Configuration Flow Control Disable Enable Ingress Rate Limit • No Limit Page 4.3.2 Port Status 4.3.3 Port Statistics 4.4 Converter Configuration 4.5 VLAN 802.1Q Tag Adding an IEEE802.1Q Tag Port VLAN ID 4.5.1 VLAN Group VLAN Mode Management VLAN Group VLAN1 VLAN Group VID 4.5.2 VLAN Per Port Setting 4.5.3 Q-in-QVLAN Setting 4.6 Quality of Service Qos Mode 802.1p Tag Priority IP Address Priority IP DSCP Priority Scheduling Page 4.7 OAM Setup 4.7.1 Local TS-1000OAM Setup 4.7.2 Remote TS-1000OAM Setup Page 4.7.3 TS-1000Loop Back Test TS-1000Loop Back Test Send Packet Number TS-1000Loop Back Test Result Result Result counter 4.7.4 802.3ah Setup 4.7.5802.3ah Loop Back Test 802.3ah Loop Back Test Packet Length (Not include CRC) 802.3ah Loop Back Test Result 4.8 Security 4.9 Logout 5. TROUBLESHOOTING The Link LED is not lit Performance is bad 10/100/1000Base-Tport link LED is lit, but the traffic is irregular Reset APPENDIX A NETWORKING CONNECTION A.1 Device‘s RJ-45Pin Assignments A.2 RJ-45cable pin assignment A.3 Fiber Optical Cable Connection Parameter Standard Fiber Diameter (micron) Modal Bandwidth A.4 Power Information A.5 Available Modules 2080-AA3450-002 EC Declaration of Conformity GT-90xynn : Planet Technology Corp Taiwan PLANET TECHNOLOGY CORPORATION