Manuals / Brands / TV and Video / TV Converter Box / Planet Technology / TV and Video / TV Converter Box

Planet Technology 2.2.2 Chassis Installation and Rack Mounting, Step, Step, Step, Step, Step, Figure, 10-inch, 19-inch, Caution:, Stand-alone, Installation

Models: GT-902 GT-902S GT-905A GT-906A15 GT-906A60 GT-906B15 GT-906B60

1 62

Download 62 pages, 5.52 Mb

2.2.2 Chassis Installation and Rack Mounting

To install the Managed Media Converter in a 10-inchor 19-inchwith standard rack, follow the instructions described below.

Step 1: Place your Managed Media Converter on a hard flat surface, with the front panel positioned towards your front side.

Step 2: Carefully slide in the module until it is fully and firmly fitted into the slot of the chassis.

Figure 2-5: Insert a Managed Media Converter into an available slot

Step 3: Attach a rack-mount bracket to each side of the Chassis with supplied screws attached to the package.

Step 4: After the brackets are attached to the chassis, use suitable screws to securely attach the brackets to the rack, as shown in Figure 2-6.

Step 5: Precede with the steps 4 and steps 5 of session 2.2.1 Stand-alone Installation to connect the network cabling and supply power to your Chassis.

Caution: You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty.

-10-

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning WEEE Warning TABLE OF CONTENTS 1. INTRODUCTION 3. MEDIA CONVERTER MANAGEMENT 5. TROUBLESHOOTING APPENDIX A NETWORKING CONNECTION 1. INTRODUCTION 1.1 Package Contents 1.2 How to Use This Manual 1.3 About the Managed Media Converter ■Application Fiber-opticNetworking for ISP, enterprise, and home 1.4Product Features 1.5PRODUCT SPECIFICATION Power Consumption Power Input Dimensions Operator Environment Storage Environment 2. HARDWARE DESCRIPTION 2.1 GT-90XFront Panel 2.1.1 LED Indicators 2.1.2GT-90XRear Panel 2.2 Install the Converter 2.2.1 Stand-aloneInstallation „GT-905AInstallation Stand-alone Installation 2.2.2 Chassis Installation and Rack Mounting Page 3. MEDIA CONVERTER MANAGEMENT 3.1 Overview 3.2 Management Methods 3.2.1 Web Management 3.2.2 SNMP Management 3.2.3 PLANET Smart Discovery Utility 3.2.4Login the Managed Media Converter 4. WEB MANAGEMENT 4.1 Main Menu 4.2 System 4.2.1 System Information 4.2.2 IP Configuration 4.2.3 Password Setting 4.2.4 Firmware Upgrade “Browser” “Upgrade” “here” Page 4.2.5 SNMP Management SNMP Trap SNMP Trap Destination Cold Start Trap Event Warm Start 4.2.6 Factory Default 4.2.7 System Reboot Page 4.3 Port Management 4.3.1 Port Configuration Flow Control Disable Enable Ingress Rate Limit • No Limit Page 4.3.2 Port Status 4.3.3 Port Statistics 4.4 Converter Configuration 4.5 VLAN 802.1Q Tag Adding an IEEE802.1Q Tag Port VLAN ID 4.5.1 VLAN Group VLAN Mode Management VLAN Group VLAN1 VLAN Group VID 4.5.2 VLAN Per Port Setting 4.5.3 Q-in-QVLAN Setting 4.6 Quality of Service Qos Mode 802.1p Tag Priority IP Address Priority IP DSCP Priority Scheduling Page 4.7 OAM Setup 4.7.1 Local TS-1000OAM Setup 4.7.2 Remote TS-1000OAM Setup Page 4.7.3 TS-1000Loop Back Test TS-1000Loop Back Test Send Packet Number TS-1000Loop Back Test Result Result Result counter 4.7.4 802.3ah Setup 4.7.5802.3ah Loop Back Test 802.3ah Loop Back Test Packet Length (Not include CRC) 802.3ah Loop Back Test Result 4.8 Security 4.9 Logout 5. TROUBLESHOOTING The Link LED is not lit Performance is bad 10/100/1000Base-Tport link LED is lit, but the traffic is irregular Reset APPENDIX A NETWORKING CONNECTION A.1 Device‘s RJ-45Pin Assignments A.2 RJ-45cable pin assignment A.3 Fiber Optical Cable Connection Parameter Standard Fiber Diameter (micron) Modal Bandwidth A.4 Power Information A.5 Available Modules 2080-AA3450-002 EC Declaration of Conformity GT-90xynn : Planet Technology Corp Taiwan PLANET TECHNOLOGY CORPORATION