Planet Technology WSW-2401 78

7Click “OK”

8When Switch client has associated with WSW-2401, a user authentication notice appears in system tray. Click on the notice to continue and get the authentication from your Windows 2000 server.

Contents

24 Ports + 1 slot Managed Ethernet Switch WSW-2401 User’s Manual Trademarks Revision TABLE OF CONTENTS CHAPTER 3 CONSOLE AND TELNET MANAGEMENT CHAPTER 6 TECHNICAL SPECIFICATION APPENDIX B Page Chapter 1 Introduction 1.1 Checklist 1.2 About the Switch 1.3 Product Feature Chapter 2 HARDWARE INSTALLATION 2.1 Font Panel FDX/COL 10/100Mbps Ethernet ports 100Base-FXModule (Optional) Console ports Hyper Terminal 2.2 Rear Panel 2.3 Hardware installation Module installation Chapter 3 Console and Telnet Management 3.1 connect To PC by RS-232cable 3.2 Telnet 3.3 Main Menu 3.4 Status and Counters 3.4-1Port Status 3.4-2Port Counters 3.4-3System Information 3.5 Switch Configuration 3.5-1Administration Configuration 3.5-1-1Device Information 3.5-1-2IP Configuration 3.5-1-3User Name Configuration Page 3.5-1-4Password Configuration 3.5-2Port configuration 3.5-3Trunk Configuration 3.5-4Port Mirroring Configuration 3.5-5VLAN Configuration 3.5-5-1VLAN configure 3.5-5-2Create VLAN Group 3.5-5-3Edit/Delete VLAN Group 3.5-5-4Group Stored Mode 3.5-5-5Previous Menu 3.5-6Priority Configuration 3.5-7MAC Address Configuration 3.5-7-1Static MAC Address 3.5-7-2Filtering MAC Address 3.5-7-3Previous Menu 3.5-8Misc Configuration 3.5-9Main Menu 3.6 Protocol Related Configuration 3.6-1STP Configuration 3.6-1-1STP setup 3.6-1-2System Configuration 3.6-1-3Per Port Setting 3.6-1-4Previous Menu 3.6-2SNMP Configuration 3.6-2-1System Options 3.6-2-2Community Strings 3.6-2-3Trap Managers 3.6-3LACP Configuration 3.6-3-1Working Ports 3.6-3-2State Activity 3.6-3-3Group Status 3.6-3-4Previous Menu 3.6-4IGMP/GVRP Configuration 3.6-5802.1X Configuration 3.6-5-1802.1x Setup 3.6-5-2System Configuration 3.6-5-3Per Port Setting 3.6-5-4Misc Configuration 3.6-5-5Previous Menu 3.7 System Reset Configuration 3.7-1Factory Default 3.7-2System Reboot 3.7-3TFTP Configuration 3.7-3-1Update Firmware 3.7-3-2Restore Configuration 3.7-3-3Backup Configuration 3.8 Logout Chapter 4 WEB MANAGEMENT 4.1 login into switch 4.2 Port Status 4.3 Port Statistics 4.4 Administrator 4.4-1IP Configuration 4.4-2Switch Settings 4.4-2-1Basic 4.4-2-2Advanced 4.4-2-3Misc Config 4.4-3Console port Information 4.4-4Port Controls 4.4-5Trunking 4.4-5-1Aggregator Setting 4.4-5-2Aggregator Information 4.4-5-3State Activity 4.4-6Forwarding and Filtering 4.4-6-1IGMP Snooping 4.4-6-2Static MAC Addresses 4.4-6-3MAC Filtering 4.4-7VLAN Configuration 4.4-7-1IEEE802.1Q ØSelect 802.1Q mode from VLAN Operation Mode Enable GVRP Protocol Next 4.4-7-2 Port-basedVLAN 4.4-7-3Port VLAN ID 4.4-8Spanning Tree 4.4-8-2Per Port configuration 4.4-9Port Mirroring 4.4-10SNMP Management 4.4-11Security Manager 4.4-12802.1x configuration 4.4-12-1System Configuration 4.4-12-2Per Port Configuration 4.4-12-3Misc Configuration 4.4-13TFTP Update Firmware 4.4-14Configuration Backup 4.4-14-1TFTP Restore Configuration 4.4-14-2TFTP Backup Configuration 4.4-15Factory Default 4.4-16System Reboot Chapter 5 TROUBLESHOOTING Chapter 6 TECHNICAL SPECIFICATION APPENDIX A A.1 Switch‘s RJ-45Pin Assignments A.2 10/100Mbps, 10/100Base-TX A.3 RJ-45cable pin assignment APPENDIX B B.1 802.1X Infrastructure B.2 RADIUS Server Setup Page Authenticated Session Smartcard Logon Properties Page Finish Start > Run command 20.Type “secedit/refreshpolicy machine_policy” to refresh policy Page Client address Client-Vendor Shared secret Confirmed shared secret 27.Click “Finish” 29.Select “New Remote Access Policy” Day-And-Time-Restriction Page Page Page Page Page Dial-in Allow access Call-back B.3 Switch client setup