Planet Technology WSW-2401 Module installation

Module installation

The slot on the font panel is purposed for installing optional modules. Following steps is described how to install a module.

1.Power off the switch.

2.Removing the two screws on the faceplate of slot with a flat-head screwdriver.

3.Push the module gently into the slot along the slide tracks.

4.Ensuring that it firmly engages with the connector then tighten the screws to secure the module.

Contents

24 Ports + 1 slot Managed Ethernet Switch WSW-2401 User’s Manual Trademarks Revision TABLE OF CONTENTS CHAPTER 3 CONSOLE AND TELNET MANAGEMENT CHAPTER 6 TECHNICAL SPECIFICATION APPENDIX B Page Chapter 1 Introduction 1.1 Checklist 1.2 About the Switch 1.3 Product Feature Chapter 2 HARDWARE INSTALLATION 2.1 Font Panel FDX/COL 10/100Mbps Ethernet ports 100Base-FXModule (Optional) Console ports Hyper Terminal 2.2 Rear Panel 2.3 Hardware installation Module installation Chapter 3 Console and Telnet Management 3.1 connect To PC by RS-232cable 3.2 Telnet 3.3 Main Menu 3.4 Status and Counters 3.4-1Port Status 3.4-2Port Counters 3.4-3System Information 3.5 Switch Configuration 3.5-1Administration Configuration 3.5-1-1Device Information 3.5-1-2IP Configuration 3.5-1-3User Name Configuration Page 3.5-1-4Password Configuration 3.5-2Port configuration 3.5-3Trunk Configuration 3.5-4Port Mirroring Configuration 3.5-5VLAN Configuration 3.5-5-1VLAN configure 3.5-5-2Create VLAN Group 3.5-5-3Edit/Delete VLAN Group 3.5-5-4Group Stored Mode 3.5-5-5Previous Menu 3.5-6Priority Configuration 3.5-7MAC Address Configuration 3.5-7-1Static MAC Address 3.5-7-2Filtering MAC Address 3.5-7-3Previous Menu 3.5-8Misc Configuration 3.5-9Main Menu 3.6 Protocol Related Configuration 3.6-1STP Configuration 3.6-1-1STP setup 3.6-1-2System Configuration 3.6-1-3Per Port Setting 3.6-1-4Previous Menu 3.6-2SNMP Configuration 3.6-2-1System Options 3.6-2-2Community Strings 3.6-2-3Trap Managers 3.6-3LACP Configuration 3.6-3-1Working Ports 3.6-3-2State Activity 3.6-3-3Group Status 3.6-3-4Previous Menu 3.6-4IGMP/GVRP Configuration 3.6-5802.1X Configuration 3.6-5-1802.1x Setup 3.6-5-2System Configuration 3.6-5-3Per Port Setting 3.6-5-4Misc Configuration 3.6-5-5Previous Menu 3.7 System Reset Configuration 3.7-1Factory Default 3.7-2System Reboot 3.7-3TFTP Configuration 3.7-3-1Update Firmware 3.7-3-2Restore Configuration 3.7-3-3Backup Configuration 3.8 Logout Chapter 4 WEB MANAGEMENT 4.1 login into switch 4.2 Port Status 4.3 Port Statistics 4.4 Administrator 4.4-1IP Configuration 4.4-2Switch Settings 4.4-2-1Basic 4.4-2-2Advanced 4.4-2-3Misc Config 4.4-3Console port Information 4.4-4Port Controls 4.4-5Trunking 4.4-5-1Aggregator Setting 4.4-5-2Aggregator Information 4.4-5-3State Activity 4.4-6Forwarding and Filtering 4.4-6-1IGMP Snooping 4.4-6-2Static MAC Addresses 4.4-6-3MAC Filtering 4.4-7VLAN Configuration 4.4-7-1IEEE802.1Q ØSelect 802.1Q mode from VLAN Operation Mode Enable GVRP Protocol Next 4.4-7-2 Port-basedVLAN 4.4-7-3Port VLAN ID 4.4-8Spanning Tree 4.4-8-2Per Port configuration 4.4-9Port Mirroring 4.4-10SNMP Management 4.4-11Security Manager 4.4-12802.1x configuration 4.4-12-1System Configuration 4.4-12-2Per Port Configuration 4.4-12-3Misc Configuration 4.4-13TFTP Update Firmware 4.4-14Configuration Backup 4.4-14-1TFTP Restore Configuration 4.4-14-2TFTP Backup Configuration 4.4-15Factory Default 4.4-16System Reboot Chapter 5 TROUBLESHOOTING Chapter 6 TECHNICAL SPECIFICATION APPENDIX A A.1 Switch‘s RJ-45Pin Assignments A.2 10/100Mbps, 10/100Base-TX A.3 RJ-45cable pin assignment APPENDIX B B.1 802.1X Infrastructure B.2 RADIUS Server Setup Page Authenticated Session Smartcard Logon Properties Page Finish Start > Run command 20.Type “secedit/refreshpolicy machine_policy” to refresh policy Page Client address Client-Vendor Shared secret Confirmed shared secret 27.Click “Finish” 29.Select “New Remote Access Policy” Day-And-Time-Restriction Page Page Page Page Page Dial-in Allow access Call-back B.3 Switch client setup