Polk Audio RMDS-1Specifications System, Overall Frequency Response 30Hz—24kHz, Satellites

RMDS-1 Specifications

System

Overall Frequency Response 30Hz—24kHz

-3dB Frequency Response Limits 38Hz—20kHz

Subwoofer to Satellite/Center Crossover Design

Active 4th order (24dB/octave) low-pass and high-pass, 150Hz acoustic crossover.

Maximum Sound Pressure Level

105 dB in an IEC Standard 80 cubic meter (2825 cubic foot, e.g. 15'W x 22'L x 81⁄2'H) room

Satellites

Driver Complement:

1-31⁄4" magnetically shielded midrange driver with polypropylene cone and butyl rubber surround

1-3⁄4" silk dome tweeter w/neodymium magnet (self shielded)

Crossover Design:

2nd order (12dB per octave slopes, electrical) symmetrical topology; mid-tweeter crossover @ 3.1 kHz; Mylar film capacitors in tweeter’s signal path.

Dimensions: 4"W x 63⁄4"H x 5"D

Center Channel

Driver Complement:

2-31⁄4" magnetically shielded drivers with polypropylene cones and butyl rubber surrounds

1-3⁄4" silk dome tweeter w/neodymium magnet (self shielded)

Crossover design:

2nd order (12dB per octave slopes, electrical) symmetrical topology; mid-tweeter crossover @ 2.5 kHz; Mylar film capacitors in tweeter’s signal path.

Dimensions:

111⁄2"W x 41⁄2"H x 53⁄4"D

Subwoofer

Driver Complement:

1-10" magnetically shielded driver with 11⁄2" voice coil, polypropylene cone and butyl rubber surround

Crossover design:

Fixed, active 4th order (24dB/octave) low-pass with amplitude shaping

Cabinet Dimensions:

151⁄2"W x 183⁄4"H x 191⁄2"D

Six Channel Power Amplifier

System Continuous Power Output Greater than 500 Watts into 4 Ohms, all channels driven*

Dynamic Power Output:

700 watts into 4 Ohms, all channels driven*

Bandwidth 20Hz-22kHz

Distortion 0.05%

Power Requirement

AC 120V, 50/60Hz

Maximum Power Consumption

800 Watts

Preamp/Processor
FM Tuner Section
Usable Sensitivity	IHF 1.3 eV/13.5dBf
Signal to noise ratio	Mono/Stereo 76/68dB
Distortion	Mono/Stereo 0.2/0.5%
Stereo Separation	1 kHz 40dB
Alternate Channel Selectivity	± 400kHz 65dB
Image Rejection	98 MHz 50dB
AM Tuner Section
Usable Sensitivity:	Loop 500µV
Signal to noise ratio	50dB
Selectivity	± 20kHz 70dB
Image Rejection	98 MHz 50dB
General
Power Requirement	AC 120V 60Hz
Power Consumption (AC-3 RF)	26W
Dimensions (Max)	171⁄4"W x 41⁄2"H x 14"D

*Power ratings alone cannot predict actual sound output. Loudspeaker efficiency is by far the most important factor in determining how loud your system will play. For this reason we also specify the calculated maximum sound output of the RMDS-1 system in a 2825 cu ft. room (for example, one measuring approximately 15'W x 22'L x 81⁄2'H). The maximum SPL (volume) of the RMDS-1 in such a room would be 105 dB, as loud as

a rock band at 150 feet; certainly loud enough to get you evicted from a New York City apartment. There are worse fates.

30 Polk customer service (800) 377-7655