Manuals / Brands / Power Tools / Saw / Porter-Cable / Power Tools / Saw

Porter-Cable 4210 & 4212 THROUGH-DOVETAIL, SKIPPED-PIN METHOD

1 44

Download 44 pages, 2.19 Mb

19

Fig. 28B

Fig. 28A

Fig. 28C

MITERING THE TAILS

On the inside surface, use a square and pencil to draw a line from the base of the tails to the edge where

the miter will be cut (Fig. 29A).

Set the table saw blade so that the height of cut of the saw blade is the same as the thickness of the

mitered half-pin.

Use a table saw with the miter gauge set to 45°to miter the tails. You will need to make several passes

to cut out the material (Fig. 29B).

NOTE: A dado head could be used to make this cut in one pass.

Step 1 -

Step 2 -

Step 3 -

FITTING THE JOINT

You may need to trim the miter cuts by hand for a good fit. Files, chisels, shoulder planes, and rabbet planes work

well. Otherwise, adjust the tightness of the joint the same as you would for a normal through dovetail.

Fig. 29A Fig. 29B Fig. 29C

THROUGH-DOVETAIL, SKIPPED-PIN METHOD

This method is very similar to cutting standard through- dovetails (Fig. 30A).

CUTTING THE TAILS

Fig. 30A

Cut the tails as normal, except do not cut into the areas where you do not want a pin to appear.

Fig. 31A

Contents

Main TABLE OF CONTENTS Back Cover SAFETY GUIDELINES - DEFINITIONS IMPORTANT SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. ADDITIONAL SAFETY RULES REPLACEMENT PARTS BACKGROUND INFORMATION OPERATION MISCELLANEOUS TECHNIQUES STOP NUT FOR BRASS ADJUSTMENT KNOB USE A DEAD-BLOW HAMMER CHAMFER THE TAIL EDGES THROUGH-DOVETAILS WITH CLAMPING BOARDS TEMPLATES MOUNTED TO CLAMPING BOARDS Page THROUGH-DOVETAILS WITH UNLIMITED BOARD WIDTH Page ALTERNATE METHOD THROUGH-DOVETAILS WITH UNLIMITED BOARD WIDTH HALF-BLIND DOVETAILS WITH CLAMPING BOARDS CUTTING THE JOINT USING A ROUTER TABLE HALF-BLIND DOVETAIL BITS THROUGH-DOVETAIL BIT COMBINATIONS (READILY AVAILABLE) ALTERNATE ROUTER BITS THROUGH-DOVETAIL BITS HALF-BLIND DOVETAIL BIT (READILY AVAILABLE) BIT COMBINATIONS FOR SEPARATE HALF-BLIND CUTS (READILY AVAILABLE) HALF-BLIND DOVETAIL BITS WITH THE TAILS AND PINS CUT SEPARATELY DOVETAIL DADO BITS BOX JOINT BITS BOX JOINT BITS (READILY AVAILABLE) HALF-BLIND DOVETAILS WITH TAIL BOARDS THICKER THAN 7/8" MITERING THE PINS MITERED THROUGH-DOVETAIL MITERING THE TAILS THROUGH-DOVETAIL, SKIPPED-PIN METHOD HALF-BLIND DOVETAIL, SKIPPED PIN METHOD Page SAW KERF ALLOWANCE METHOD Page END-TO-END JOINTS BOX END-TO-END JOINTS FITTING AND CUTTING THE JOINT MULTIPLE SPACER METHOD DOVETAIL END-TO-END JOINTS DRAWERS WITH DOVETAIL DADOS 180 HINGES WITH A DRILLED HOLE WOODEN HINGES 270 HINGES WITH A DRILLED HOLE 180 HINGES WITH ROUTER-MADE GROOVES 270 HINGES WITH ROUTER-MADE GROOVES ANGLED JOINTS OBTUSE ANGLED JOINTS SETUP WITH THE TEMPLATE MOUNTED TO THE BASE OF THE JIG CUTTING THE TAILS SETUP WITH THE TEMPLATE MOUNTED TO A CLAMPING BOARD CUTTING THE PINS ACUTE ANGLED JOINTS SLANTED-SIDE JOINTS COMPOUND-ANGLE JOINTS SETUP CUTTING THE PINS CUTTING THE TAILS INLAYED JOINTS INLAYED THROUGH DOVETAIL INLAYED HALF-BLIND DOVETAIL Page INLAYED BOX JOINT THROUGH DOVETAIL ROUTER BIT COMBINATIONS TABLES OF COMMONLY AVAILABLE ROUTER BIT SIZES HALF-BLIND DOVETAIL BITS COMBINATIONS FOR HALF-BLIND DOVETAILS WITH THE PINS AND THE TAILS CUT SEPARATELY. * BOX JOINT BIT COMBINATIONS REPLACEMENT PARTS SERVICE AND REPAIRS SERVICE ACCESSORIES TROUBLESHOOTING MAINTENANCE KEEP TOOL CLEAN WARRANTY PORTER-CABLE LIMITED ONE YEAR WARRANTY The following are trademarks of PORTER-CABLE DELTA (Las siguientes son marcas registradas de PORTER-CABLE PORTER-CABLE DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE DELTA) Delta ms cercano. Delta deben obtenerse ponindose en contacto con cualquier distribuidor Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service Center, or Porter-Cable