Manuals / Powermatic / Power Tools / Biscuit Joiner

Powermatic 60C, 60HH operating instructions New Sanford Rd LaVergne, TN Phone

Models: 60HH

1 44

Download 44 pages 25.26 Kb

Page 44

427 New Sanford Rd.

427 New Sanford Rd.

LaVergne, TN 37086

Phone: 800-274-6848

www.powermatic.com

44

Image 44

Powermatic 60C, 60HH operating instructions New Sanford Rd LaVergne, TN Phone

Contents

Powermatic Part No. M-16100848-inch Jointer Operating Instructions and Parts ManualWarranty and Service Warranty PeriodWhat is Covered Warranty LimitationsTable of Contents 3. Replace the warning labels if they become obscured or removed Lead from lead based paintCrystalline silica from bricks, cement and other masonry products Arsenic and chromium from chemically treated lumber24. Use recommended accessories improper accessories may be hazardous Introduction Specifications3HP 3PH 230/460V prewired Features and Terminology - 60C and 60HH Jointers Contents of the Shipping Container Unpackingsee Figures 2, 3 Included with straight cutterhead models 60C onlyAssembly Tools required for assemblyThe jointer is very heavy Exercise proper caution when lifting it Assembling Jointer to StandInstalling Drive Belt Aligning PulleysRemoving Guard Refer to FigureInstalling Belt Guard and Door Installing Switch ArmInstalling Dust Chute hose and clamp not providedInstalling Fence Handwheel Knife Gauge Assembly model 60C onlyElectrical Connections Storing the Push BlocksConverting from 230 Volt to 460 Volt Three Phase Only Grounding InstructionsAdjustments Installing and Adjusting KnivesThree-Phase Test Run Tools required for adjustmentsstraight cutterhead only 1. Disconnect machine from power sourcestraight cutterhead only Helical Cutterhead Only Replacing and Rotating Knife Insertshelical cutterhead only Refer to Figure Leveling TablesIf table will still not line up Adjusting Depth of Cut Setting Outfeed TableRapid Adjust Fine AdjustExamples of incorrect settings Spring CuttingFence Movement Refer to FigureFence Stops See Figure90-degree stop 45 degree forward stopStart - Press the green start switch When power is connected to the machine, theStop - Press the red switch to stop Reset - In the event that the Jointer stopsHand Placement Basic Jointer OperationJointing Short or Thin Work Direction of GrainBeveling Jointing Warped SurfacesEdge Jointing Refer to Figure Skewing Shear CuttingTaper Cuts Maintenance Disconnect machine from power source before doing any maintenanceRabbeting Refer to FigureCutterhead Maintenance Sharpening Knives model 60C onlyTable Removal After gib screws are loosened, table could suddenly slide downTroubleshooting - Mechanical and Electrical Problems TroubleProbable Cause RemedyTrouble Probable CauseRemedy Machine will notTroubleshooting - Operating Problems Straight cutterhead Replace nickedHelical cutterhead Rotate nicked TroubleReplacement Parts Parts List Base Assembly 60C and 60HHIndex No. Part No DescriptionSize Index No. Part NoDescription Base Assembly 60C and 60HH Parts List Fence Assembly 60C and 60HH Index No. Part NoDescription SizeFence Assembly 60C and 60HH Parts List Straight Cutterhead Assembly 60C only Index No. Part NoDescription SizeParts List Helical Cutterhead Assembly 60HH only Index No. Part NoDescription SizeParts List Stand Assembly 60C and 60HH Index No. Part NoDescription SizePM2000-105 Stand Assembly 60C and 60HH 3Ph ModelElectrical Connections - Single Phase, 230 Volt Electrical Connections - 3 Phase, 230 Volt Electrical Connections - 3 Phase, 460 Volt 427 New Sanford Rd LaVergne, TN Phone