Manuals
/
Powermatic
/
Power Tools
/
Biscuit Joiner
Powermatic
operating instructions Base Assembly 60C and 60HH
Models:
60HH
1
33
44
44
Download
44 pages
25.26 Kb
30
31
32
33
34
35
36
37
<
>
Troubleshooting
Specification
Install
Parts list
Hand Placement
Warranty
Maintenance
Reset - In the event that the Jointer stops
Assembly
Adjustments
Page 33
Image 33
Base Assembly (60C and 60HH)
33
Page 32
Page 34
Page 33
Image 33
Page 32
Page 34
Contents
Part No. M-1610084
Powermatic
8-inch Jointer
Operating Instructions and Parts Manual
Warranty Period
Warranty and Service
What is Covered
Warranty Limitations
Table of Contents
Lead from lead based paint
3. Replace the warning labels if they become obscured or removed
Crystalline silica from bricks, cement and other masonry products
Arsenic and chromium from chemically treated lumber
24. Use recommended accessories improper accessories may be hazardous
Specifications
3HP 3PH 230/460V prewired
Introduction
Features and Terminology - 60C and 60HH Jointers
Unpacking
Contents of the Shipping Container
see Figures 2, 3
Included with straight cutterhead models 60C only
Tools required for assembly
Assembly
The jointer is very heavy Exercise proper caution when lifting it
Assembling Jointer to Stand
Aligning Pulleys
Installing Drive Belt
Removing Guard
Refer to Figure
Installing Switch Arm
Installing Belt Guard and Door
Installing Dust Chute
hose and clamp not provided
Knife Gauge Assembly model 60C only
Installing Fence Handwheel
Electrical Connections
Storing the Push Blocks
Grounding Instructions
Converting from 230 Volt to 460 Volt Three Phase Only
Installing and Adjusting Knives
Adjustments
Three-Phase Test Run
Tools required for adjustments
1. Disconnect machine from power source
straight cutterhead only
straight cutterhead only
Replacing and Rotating Knife Inserts
helical cutterhead only
Helical Cutterhead Only
Leveling Tables
If table will still not line up
Refer to Figure
Setting Outfeed Table
Adjusting Depth of Cut
Rapid Adjust
Fine Adjust
Spring Cutting
Examples of incorrect settings
Fence Movement
Refer to Figure
See Figure
Fence Stops
90-degree stop
45 degree forward stop
When power is connected to the machine, the
Start - Press the green start switch
Stop - Press the red switch to stop
Reset - In the event that the Jointer stops
Basic Jointer Operation
Hand Placement
Jointing Short or Thin Work
Direction of Grain
Jointing Warped Surfaces
Edge Jointing
Beveling
Skewing Shear Cutting
Taper Cuts
Refer to Figure
Disconnect machine from power source before doing any maintenance
Maintenance
Rabbeting
Refer to Figure
Sharpening Knives model 60C only
Cutterhead Maintenance
After gib screws are loosened, table could suddenly slide down
Table Removal
Trouble
Troubleshooting - Mechanical and Electrical Problems
Probable Cause
Remedy
Probable Cause
Trouble
Remedy
Machine will not
Straight cutterhead Replace nicked
Troubleshooting - Operating Problems
Helical cutterhead Rotate nicked
Trouble
Parts List Base Assembly 60C and 60HH
Replacement Parts
Index No. Part No
Description
Index No. Part No
Description
Size
Base Assembly 60C and 60HH
Index No. Part No
Parts List Fence Assembly 60C and 60HH
Description
Size
Fence Assembly 60C and 60HH
Index No. Part No
Parts List Straight Cutterhead Assembly 60C only
Description
Size
Index No. Part No
Parts List Helical Cutterhead Assembly 60HH only
Description
Size
Index No. Part No
Parts List Stand Assembly 60C and 60HH
Description
Size
PM2000-105
3Ph Model
Stand Assembly 60C and 60HH
Electrical Connections - Single Phase, 230 Volt
Electrical Connections - 3 Phase, 230 Volt
Electrical Connections - 3 Phase, 460 Volt
427 New Sanford Rd LaVergne, TN Phone