Manuals / Powermatic / Power Tools / Biscuit Joiner

Powermatic 60C, 60HH operating instructions Electrical Connections - 3 Phase, 230 Volt

Models: 60HH

1 44

Download 44 pages 25.26 Kb

Page 42

Image 42

Electrical Connections – 3 Phase, 230 Volt

Page 42

Image 42

Powermatic 60C, 60HH operating instructions Electrical Connections - 3 Phase, 230 Volt

Contents

8-inch Jointer PowermaticPart No. M-1610084 Operating Instructions and Parts ManualWhat is Covered Warranty and ServiceWarranty Period Warranty LimitationsTable of Contents Crystalline silica from bricks, cement and other masonry products 3. Replace the warning labels if they become obscured or removedLead from lead based paint Arsenic and chromium from chemically treated lumber24. Use recommended accessories improper accessories may be hazardous Specifications 3HP 3PH 230/460V prewiredIntroduction Features and Terminology - 60C and 60HH Jointers see Figures 2, 3 Contents of the Shipping ContainerUnpacking Included with straight cutterhead models 60C onlyThe jointer is very heavy Exercise proper caution when lifting it AssemblyTools required for assembly Assembling Jointer to StandRemoving Guard Installing Drive BeltAligning Pulleys Refer to FigureInstalling Dust Chute Installing Belt Guard and DoorInstalling Switch Arm hose and clamp not providedElectrical Connections Installing Fence HandwheelKnife Gauge Assembly model 60C only Storing the Push BlocksConverting from 230 Volt to 460 Volt Three Phase Only Grounding InstructionsThree-Phase Test Run AdjustmentsInstalling and Adjusting Knives Tools required for adjustments1. Disconnect machine from power source straight cutterhead onlystraight cutterhead only Replacing and Rotating Knife Inserts helical cutterhead onlyHelical Cutterhead Only Leveling Tables If table will still not line upRefer to Figure Rapid Adjust Adjusting Depth of CutSetting Outfeed Table Fine AdjustFence Movement Examples of incorrect settingsSpring Cutting Refer to Figure90-degree stop Fence StopsSee Figure 45 degree forward stopStop - Press the red switch to stop Start - Press the green start switchWhen power is connected to the machine, the Reset - In the event that the Jointer stopsJointing Short or Thin Work Hand PlacementBasic Jointer Operation Direction of GrainJointing Warped Surfaces Edge JointingBeveling Skewing Shear Cutting Taper CutsRefer to Figure Rabbeting MaintenanceDisconnect machine from power source before doing any maintenance Refer to FigureCutterhead Maintenance Sharpening Knives model 60C onlyTable Removal After gib screws are loosened, table could suddenly slide downProbable Cause Troubleshooting - Mechanical and Electrical ProblemsTrouble RemedyRemedy TroubleProbable Cause Machine will notHelical cutterhead Rotate nicked Troubleshooting - Operating ProblemsStraight cutterhead Replace nicked TroubleIndex No. Part No Replacement PartsParts List Base Assembly 60C and 60HH DescriptionIndex No. Part No DescriptionSize Base Assembly 60C and 60HH Description Parts List Fence Assembly 60C and 60HHIndex No. Part No SizeFence Assembly 60C and 60HH Description Parts List Straight Cutterhead Assembly 60C onlyIndex No. Part No SizeDescription Parts List Helical Cutterhead Assembly 60HH onlyIndex No. Part No SizeDescription Parts List Stand Assembly 60C and 60HHIndex No. Part No SizePM2000-105 Stand Assembly 60C and 60HH 3Ph ModelElectrical Connections - Single Phase, 230 Volt Electrical Connections - 3 Phase, 230 Volt Electrical Connections - 3 Phase, 460 Volt 427 New Sanford Rd LaVergne, TN Phone