Manuals / Powermatic / Power Tools / Biscuit Joiner

Powermatic 60HH, 60C operating instructions Electrical Connections - Single Phase, 230 Volt

Models: 60HH

1 44

Download 44 pages 25.26 Kb

Page 41

Image 41

Electrical Connections – Single Phase, 230 Volt

Page 41

Image 41

Powermatic 60HH, 60C operating instructions Electrical Connections - Single Phase, 230 Volt

Contents

Part No. M-1610084 Powermatic8-inch Jointer Operating Instructions and Parts ManualWarranty Period Warranty and ServiceWhat is Covered Warranty LimitationsTable of Contents Lead from lead based paint 3. Replace the warning labels if they become obscured or removedCrystalline silica from bricks, cement and other masonry products Arsenic and chromium from chemically treated lumber24. Use recommended accessories improper accessories may be hazardous Introduction Specifications3HP 3PH 230/460V prewired Features and Terminology - 60C and 60HH Jointers Unpacking Contents of the Shipping Containersee Figures 2, 3 Included with straight cutterhead models 60C onlyTools required for assembly AssemblyThe jointer is very heavy Exercise proper caution when lifting it Assembling Jointer to StandAligning Pulleys Installing Drive BeltRemoving Guard Refer to FigureInstalling Switch Arm Installing Belt Guard and DoorInstalling Dust Chute hose and clamp not providedKnife Gauge Assembly model 60C only Installing Fence HandwheelElectrical Connections Storing the Push BlocksGrounding Instructions Converting from 230 Volt to 460 Volt Three Phase OnlyInstalling and Adjusting Knives AdjustmentsThree-Phase Test Run Tools required for adjustmentsstraight cutterhead only 1. Disconnect machine from power sourcestraight cutterhead only Helical Cutterhead Only Replacing and Rotating Knife Insertshelical cutterhead only Refer to Figure Leveling TablesIf table will still not line up Setting Outfeed Table Adjusting Depth of CutRapid Adjust Fine AdjustSpring Cutting Examples of incorrect settingsFence Movement Refer to FigureSee Figure Fence Stops90-degree stop 45 degree forward stopWhen power is connected to the machine, the Start - Press the green start switchStop - Press the red switch to stop Reset - In the event that the Jointer stopsBasic Jointer Operation Hand PlacementJointing Short or Thin Work Direction of GrainBeveling Jointing Warped SurfacesEdge Jointing Refer to Figure Skewing Shear CuttingTaper Cuts Disconnect machine from power source before doing any maintenance MaintenanceRabbeting Refer to FigureSharpening Knives model 60C only Cutterhead MaintenanceAfter gib screws are loosened, table could suddenly slide down Table RemovalTrouble Troubleshooting - Mechanical and Electrical ProblemsProbable Cause RemedyProbable Cause TroubleRemedy Machine will notStraight cutterhead Replace nicked Troubleshooting - Operating ProblemsHelical cutterhead Rotate nicked TroubleParts List Base Assembly 60C and 60HH Replacement PartsIndex No. Part No DescriptionSize Index No. Part NoDescription Base Assembly 60C and 60HH Index No. Part No Parts List Fence Assembly 60C and 60HHDescription SizeFence Assembly 60C and 60HH Index No. Part No Parts List Straight Cutterhead Assembly 60C onlyDescription SizeIndex No. Part No Parts List Helical Cutterhead Assembly 60HH onlyDescription SizeIndex No. Part No Parts List Stand Assembly 60C and 60HHDescription SizePM2000-105 3Ph Model Stand Assembly 60C and 60HHElectrical Connections - Single Phase, 230 Volt Electrical Connections - 3 Phase, 230 Volt Electrical Connections - 3 Phase, 460 Volt 427 New Sanford Rd LaVergne, TN Phone