Raise | Precor C934 manual

C O M M E R C I A L P R O D U C T S D I V I S I O N

Diagram 9	Raise the
	incline.
	Side rail
	Incline lift
	QUICKSTARTTM
	key

Important: With the handrails attached, the width of the treadmill is 33½ inches (85 cm). It will not fit through a standard 32-inch doorway.

10.Prepare the unit for handrail installation. Diagram 9.For an easier installation, raise the incline to its maximum height by taking the following steps:

a.Plug the treadmill into a power outlet and turn the unit ON.

b.Stand to the side of the treadmill and press QUICKSTART (see inset). After a few seconds, the running belt begins moving.

c.Press the INCLINE ▲ key until the display shows an incline of 15 percent.

d.Once the lift stops moving and the display indicates 15 percent, press the Stop (red) button and turn power switch OFF.

Diagram 10	Remove the
	lower handrail
	clamp.
	Lower handrail
	clamp
	Loosen and
	remove the four
	handrail clamp
	screws.

11.Remove the lower handrail clamp. Diagram 10. To prepare the unit for handrail installation, remove the four fasteners securing the lower handrail clamp. Use the hex key provided.

page 15

Image 15

Precor C934 owner manual Raise

Contents

C934 Important Safety Instructions Grounding Instructions Safety Approval Table of Contents Maintenance Exercising on the TreadmillCourses Radio Frequency Interference RFI European ApplicationsVoid the user’s authority to operate the equipment About this Manual Obtaining Service M M E R C I a L P R O D U C T S D I V I S I O N Unpacking the Treadmill Standard EquipmentOther Equipment Additional Tools Needed Hardware KIT Setting Up the Treadmill Installation RequirementsAssembly Instructions Diagram Route cable Csafe Secure the display console to the upright supports. Diagram Raise Perform steps a. and b. on the opposite side Attach handrails to the side and base brackets. Diagram Test the heart rate feature. Diagram Continue with the assembly Second Level Unit Turning the Unit on and OFF If the running belt Then Checking the Alignment of the Running Belt Club Information Changing the Club Settings Determining the Units of Measure Display key functions within the Club Custom Mode To 18 kph Setting a Workout Time LimitSetting a Pause Time Limit Determining the Club Speed Limit M M E R C I a L P R O D U C T S D I V I S I O N User ID Entry Program Keys Using Csafe Standard Equipment C934 Display Features on the Display Console Smartrate Display Setup Mode and Prompts Setup Mode and the Quickstart Feature Weight prompt Following occursPrecor banner Course prompt Display Features During a Workout M M E R C I a L P R O D U C T S D I V I S I O N Keypad keys Keys on the Display Console Prompts Default Value Quickstart Default Values Changing the Display Features Using the Select KEY Exercising on the Treadmill Using the Security ClipUsing the Handrails Using the Heart Rate Touch Capability Keypad Tips Workout TipsQuick Steps to Working OUT To display the course selections, press Enter and then Stop Cooling Down After a Workout Stop PAUSE, Workout SUMMARY, and Exit Features Heart Rate Feature Using the Smartrate FeatureCourses Rate Manual Mode and the Quickstart KEY Cross Country Course Interval CourseTo use the interval course, take the following steps Random Course Weight Loss Course Heart Rate Course Perform a daily inspection of the treadmill MaintenanceCleaning the Equipment Inspection Aligning the Running Belt Storing the Polar Chest Strap Servicing the TreadmillLong Term Storage C934 C934 C934 C934 C934 C934 C934 C934 Thank You and Welcome to Precor How many members do you have? Date of Purchase Purchased from Dealer nameProduct Serial Numbers Please indicate the type and number of products purchased Complete this portion and keep for your records Limited WarrantyWarranty Periods and Coverage Conditions and Restrictions C934 Programs C934 Display Readouts Product Specifications Electronic Specifications