Assembly, Frame Positioning | Pride Mobility SC2000PS specification

I X . D I S A S S E M B LY A N D A S S E M B LY

ASSEMBLY

1.Place the manual freewheel lever in the drive (up) position.

2.Position the front and rear sections of your scooter as shown in figure 17.

WARNING! Position the front-to-rear harness cable so it will not become pinched between the frame halves when pivoting the rear section forward.

3.Align the lower slots on the rear of the front section with the corresponding pegs on the front of the rear section. See figure 18.

4.Gently lift up on the seat post on the rear section of your scooter, so the rear section pivots into place.

5.Secure the front and rear sections with the ball detent pin.

6.Raise the tiller

7.Plug the front-to-rear harness into the mating plug found on the rear electronics module.

8.Put the batteries in place and plug the black and white 2-pin battery harnesses into the rear electronics module.

9.Reconnect the battery straps.

10.Gently place the rear shroud over the seat post.

11.Lower the shroud into place.

12.Carefully lift the seat and slide the seat platform post (on the seat bottom) into the seat pedestal.

13.Rotate the seat until it locks into place.

FRONT-TO REAR HARNESS

CABLE

Figure 17. Frame Positioning

Figure 18. Connecting The Frame Halves

32

www.pridemobility.com

Sundancer

Image 32

Pride Mobility SC2000PS owner manual Assembly, Frame Positioning

Contents

Ultimate In Style & Performance F E T Y G U I D E L I N E S N T E N T S Safety N T R O D U C T I O NPURCHASER’S Agreement Information Exchange S a F E T Y GeneralModifications Removable Parts PRE-RIDE Safety Check Weight LimitationsTire Inflation Incline Information ˚ 15.8% ˚ 14.1% Cornering Information Braking Information Outdoor Driving Surfaces Correct Curb Approach Inclement Weather Precautions Freewheel ModeStairs and Escalators Doors Battery Disposal and Recycling ElevatorsLIFT/ELEVATION Products Batteries Getting Onto and OFF of Your Scooter Motor Vehicle TransportSecurement Points Reaching and Bending Positioning BeltsPrescription DRUGS/PHYSICAL Limitations Alcohol I . E M I / R F Electromagnetic and Radio Frequency Interference EMI/RFI Specification S Scooter Dimensions Model Numbers Key Switch O U R S C O O T E RTiller Console Throttle Control Lever Speed Adjustment Dial Running Lights SwitchPower Seat Switch Hazard Lights Switch Charger Power Cord Receptacle Main Circuit Breaker Reset ButtonAmmeter Manual Freewheel Lever Anti-Tip Wheels Motor/Transaxle AssemblyBatteries not shown Charging Your Batteries Reading Your Battery VoltageB a T T E R I E S a N D C H a R G I N G Batteries and CHARGING-FREQUENTLY Asked Questions Faqs How does the charger work?What if the scooter’s batteries won’t charge? Can I use a different charger? What type and size of battery should I use? How do I change a battery in my scooter? How can I ensure maximum battery life? What about public transportation? PRE-RIDE Adjustments and Checks I . O P E R a T I O NBefore Getting on Your Scooter Getting Onto Your Scooter Getting OFF of Your Scooter Remove the key from the key switchPower Down Timer Feature Tiller Angle Adjustment I I . C O M F O R T a D J U S T M E N T SLowering The Tiller To The Scooter Deck Raising The Tiller From The Scooter Deck FRONT-TO-BACK Seat Adjustment Armrest Width AdjustmentSeat Height Adjustment Power Seat Post Operating your power seat I I . C O M F O R T a D J U S T M E N T S Disassembly D I S a S S E M B LY a N D a S S E M B LY D a S S E M B LY Assembly Frame Positioning What if all the systems on my scooter seem to be dead? A S I C TroubleshootingDiagnostic Flash Codes What if the main circuit breaker repeatedly trips? C a R E a N D M a I N T E N a N C E Fuse Replacement Light Bulb ReplacementCONSOLE, CHARGER, and Rear Electronics Storing Your Scooter I . W a R R a N T Y Implied Warranties Service Checks and Warranty ServiceExclusions also include components with damage caused by Susquehanna Ave. Exeter, PA 18643