V I I I . B A S I C T R O U B L E S H O O T I N G
Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.
DIAGNOSTIC BEEP CODES
The diagnostic beep codes for your Travel Scooter are designed to help you perform basic troubleshooting quickly and easily. A diagnostic beep code will sound in the event one of the conditions listed below develops.
NOTE: Your Travel Scooter will not run unless the beep code condition is resolved and the Travel Scooter has been turned off, then turned back on.
|
| BEEP CODE |
| CONDITION |
| SOLUTION |
|
| ||
! | ! | (2) |
| Battery voltage is too low to operate the | Charge fully until charger and any meters | |||||
|
|
|
| Travel Scooter. | indicate completion. |
|
|
| ||
! | ! | ! (3) |
| Battery voltage is too high to operate the | Contact your authorized Pride Provider for | |||||
|
|
|
| Travel Scooter. | assistance. |
|
|
|
| |
! ! ! ! ! (5) |
| Solenoid brake trip. The manual freewheel | Remove the | key, | then push the | manual | ||||
| freewheel lever to the drive position, restart | |||||||||
|
|
|
| lever may be in the freewheel position. | ||||||
|
|
|
| your scooter. |
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
! ! ! ! ! ! (6) |
| Throttle trip. The throttle control lever | Release the throttle control lever completely, | |||||||
| may have been depressed while inserting | |||||||||
|
|
|
| then reinsert the key. |
|
| ||||
|
|
|
| the key. |
|
| ||||
|
|
|
|
|
|
|
|
| ||
! ! ! ! ! ! ! (7) |
| Throttle trip. Throttle potentiometer fault | Contact your authorized Pride Provider for | |||||||
|
|
|
| or speed potentiometer fault. | assistance. |
|
|
|
| |
|
|
|
| |||||||
! ! ! ! ! ! ! ! (8) |
| The Travel Scooter’s motor is | Contact your authorized Pride Provider for | |||||||
|
|
|
| disconnected. | assistance. |
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
| Possible controller trip. You may be | Shut down | your | Travel Scooter | for | a | |
|
|
|
| minimum of | several minutes to allow | the | ||||
|
|
|
| attempting to install the battery pack while | ||||||
! ! ! ! ! ! ! ! ! | (9) | controller to cool. Or, try reinserting the key | ||||||||
the key is inserted or the motor controller | ||||||||||
|
|
|
| into the key switch | and turning the | Travel | ||||
|
|
|
| may be in overheat protective mode. | ||||||
|
|
|
| Scooter on. |
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
What if all the systems on my Travel Scooter seem to be “dead”?
!Make certain that the key is in the “on” position.
!Check that the batteries are fully charged.
!Push in the main circuit breaker reset button. See III. “Your Travel Scooter.”
!Make certain that the battery pack is seated properly.
!Be sure the power down timer feature has not been activated. See V. “Operation.”
!Check the tiller console fuse located under the battery pack.
To check a fuse:
1.Remove the fuse by pulling it out of its slot.
2.Examine the fuse to be sure it is blown. See figures 24 and 25.
3.Insert a new fuse of the proper rating.
WARNING! The replacement fuse must exactly match the rating of the old fuse. Failure to use properly rated fuses may cause damage to the electrical system.
Figure 24. Working Fuse
Figure 25. Blown Fuse (Replace)
32 | www.pridemobility.com | Elite Traveller Plus/Plus HD |
