INSTALLING LOGS
WARNING: Failure to position the parts in accordance with these diagrams may result in property dam- age or personal injury.
CAUTION: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. With the heater set to HIGH, check to see if flames contact any log. If so, reposition logs according to the log installation instructions in this manual. Flames contacting logs will create soot.
IMPORTANT: Make sure log does not cover any burner ports (see Figure10).
Figure 10 -Installing One-Piece Log Set (Top View)
OPERATING HEATER
FOR YOUR SAFETYREAD BEFORE
LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing prop- erty damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
*Do not try to light any appliance.
*Do not touch any electrical switch.
*Do not use any phone in your building.
*Immediately call your gas supier from a neighbor’s phone. Follow the gas supplier’s instructions.
*If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don;t try to repair it; call a qualified service technician. Force or attempted repair may result in a fire or explosion.
INSTALLATION
Continued
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.
LIGHTING INSTRUCTIONS
1.STOP! Read the safety informatuion above.
2.Set thermostat (gas control knob) to lowest setting.
3.Turn off all electric power to the appliance (if applicable).
4.Push in gas control knob slightly and turn clockwise to “OFF”. Do not force.
5.Waitten (10) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If you don’t smell gas, go to the next step.
6.Find
7.Turn gas control knob counterclockwise to “PILOT”.
8.Push in gas control knob all the way and hold in. Repeatedly push the pieze ignitor button until pilot is lit (or use a match to light pilot). Continue to hold the control knob in for about one (1) minute after the pilot is lit. Pilot should remain lit. If it goes out, repeat steps 4 through 8.
*If knob does not pop up when released, stop and immediantely call your service technician or gas supplier.
*If pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier.
9.Attention! Gas control has an interlock latching device. When the pilot is intially lit and the safety magnet is energized (pilot stays “ON”) the INTERLOCK latching device becomes operative. If the gas control is turned to the “OFF” position or gas flow to the appliance is shut off, the pilot cannot be relighted until the safety magnet is de- energized (approximately 60 seconds). There will be an audile “click” when the safety magnet in the gas control is
10.Turn gas control knob counterclockwise to “HI”.
11.Turn on all electric power to appliance (if applicable).
12.Set thermostat (gas control knob) to desired setting from “HI” to “LO”.
9
Figure 11 -Control Knob and
Ignitor Button location
Figure 12
NOTICE: During initial operation of new heater, burning logs will give off
a
CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.
TO TURN OFF GAS TO APPLIANCE
1.Set thermostat (gas control knob) to lowest setting.
2.Turn off all electric power to appliance if service is to be performed (if applicale).
3.Push in gas control knob slightly and turn clockwise to “OFF”. Do not force.
