Manuals / Quadra-Fire / Household Appliance / Stove

Quadra-Fire 3100 owner manual Page

Models: 3100

1 32

Download 32 pages 9.09 Kb

<>

Install Accessories And Service Parts Glass Replacement Warranty Dimension Maintenance Blower Switch Adjustments Ash Removal System Operating And Cleaning How to Safety

Page 31

NOTES

Page 31

Page 30 Page 32

Image 31

Quadra-Fire 3100 owner manual Page

Page 30 Page 32

Related manuals

Manual 32 pages 9.09 Kb

Related pages Chapter 4. Troubleshooting for Lenovo S10 Model 2.5i Specifications for NHT 2.5i 4NiMH batteries will usually maintain their charge for a full day of normal classroom use. Always switch the Transmitter OFF when not in use lunch hour, quiet times, etc.. Should the batteries in the Transmitter need to be changed, open the lower plastic cover by pressing the ribbed portions on both sides of the cover located near the center of the Transmitter towards each other. At the same time, pull forward on the cover, rotating it on the hinges located at the bottom of the cover. Insert the new batteries paying attention to the + and - as indicated inside the case. Rotate the cover back toward the Transmitter center and snap it back into a locked position for LightSpeed Technologies LES 600 Series Frequently asked questions for Philips SA5115 Installation for MTX Audio THUNDER895 ILLUSTRATED PARTS LIST for Market Forge Industries ST-3E Language code list for Panasonic SC-PM86D Indicator Lights Green Mains Light for Hotpoint FZM54 Specifications for Hosa Technology HDMM-410 SAMPLE PARTS LIST for Multiquip DCA45USI2 SERVICE AND ADJUSTMENTS for Poulan PPH23B48

Contents

SAVE THESE INSTRUCTIONS INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONSNorthAmerica’sBest QUADRA-FIRE 3100 SERIESTABLE OF CONTENTS Serial No 3100 SAFETY LABEL found on back of stoveModel Quadra-FireFIGURE 1a DIMENSIONSPEDESTAL MODEL LEG MODELFIGURE 2a STEP TOP PEDESTAL MODELSTEP TOP LEG MODEL DIMENSIONSCLEARANCES TO COMBUSTIBLES UL AND ULC CHIMNEY SYSTEMS SAFETY LISTINGINSTALLATION MATERIALS NEEDED FOR YOUR SAFETY VENTING SYSTEMCHIMNEY HEIGHT/DRAFT CHIMNEY CONNECTORCONNECTION TO A MASONRY CHIMNEY The chimney must have a fire clay flue liner or equivalent with a minimum thickness of 5/8” 16mm and must be installed with refractory mortar. There must be at least ½” 13mm air space between the flue liner and the chimney wall Figure 4. An equivalent liner must be a listed chimney liner system or other approved material Remember that insulation must not contact the chimney. There must be air space around the chimney. Insulation must be 2” 50mm or more from the chimney Figure 2. THIMBLE An approved thimble must be used when the connection from the stove is made through a combustible wall to a masonry chimney. There are several methods you can use for connection through a combustible wall, two of which are illustrated in this manual. For additional methods, consult local building authorities or use the standards set forth in NFPA B. 6” SOLID PACK CHIMNEY WITH METAL SUPPORTS AS A THIMBLE For the method of installation to a masonry chimney shown in Figures 10 and 11 page 13, it will be necessary to purchase a 6” 152mm inside diameter, 12” 305mm long section of prefabricated listed solid pack chimney to use as a thimble. Purchase a wall spacer, trim collar and wall band that are manufactured to fit the chimney section you purchase. Cut out a 14 ½” 368mm diameter opening in the wall. It may be necessary to cut wall studs and install a header and sill frame to maintain the wall support. The hole in the chimney must have at least a 6” 152mm diameter fire clay liner or equivalent, secured with refractory mortar. If it is necessary to cut a hole in the chimney liner, use extreme care to keep it from shattering Page INTERIOR CHIMNEY, RUNNING THROUGH CEILING AND ROOF CONNECTION TO A METAL PREFABRICATED CHIMNEYMOBILE HOME INSTALLATION 3100 LEG MODELS OUTSIDE AIR KIT INSTALLATION3100 PEDESTAL MODELS LEG MODEL PEDESTAL/LEG KIT INSTALLATIONFOR INSTALLATION OF ASH REMOVAL SYSTEM, SEE PAGE PEDESTAL MODELPEDESTAL MODEL ASH REMOVAL SYSTEM INSTALLATIONLEG MODEL ASH REMOVAL SYSTEM OPERATING AND CLEANING OPERATING INSTRUCTIONS IMPORTANT - PLEASE READ BEFORE USING STOVE BURNING PROCESSBURNING GUIDELINES OPERATING INSTRUCTIONS contBLOWER OPERATING INSTRUCTIONS OPERATING TIPSOPERATING INSTRUCTIONS cont BURNING GUIDELINES contBUILDING A FIRE WOOD SELECTION AND STORAGECHIMNEY CLEANING MAINTENANCECARE AND CLEANING OF GLASS CARE AND CLEANING OF PLATED SURFACESGLASS REPLACEMENT DOOR HANDLE ASSEMBLYBAFFLE REMOVAL AND INSTALLATION 832-0550 Single brick 832-3010 Brick set BAFFLE REMOVAL AND INSTALLATION contBRICK PATTERN 7. Keep the baffle tilted as you lift it out the door831-1700 INSTALLATION OF OPTIONAL BLOWERBLOWER SWITCH ADJUSTMENTS STEPS FOR ADJUSTING THE BLOWER SPEED CONTROL3. Set top heat shield on stove and push down into “S” clips TOP HEAT SHIELD INSTALLATION4. Install chimney pipe through hole in top heat shield 1. Unscrew and remove the rear heat deflectorACCESSORIES ACCESSORIES AND SERVICE PARTSSERVICE PARTS Page Page NorthAmerica’sBest lifetime warrantyFOR YOUR RECORDS