FCC Notice | Radio Shack PRO-2040 guide

20-414.fm Page 4 Wednesday, August 4, 1999 11:12 AM

Your PRO-2040 can receive these bands:

Band	Modulation	Frequency Range		Frequency
				Step
10-Meter Ham Band	FM	29.00-29.7 MHz		5.0 kHz
VHF-Lo	FM	29.7-50.00 MHz		5.0 kHz
6-Meter Ham Band	FM	50.00-54.00 MHz		5.0 kHz
Aircraft	AM	108-136.975 MHz		12.5 kHz
Government/Ham	FM	137-148 MHz		5.0 kHz
VHF-Hi	FM	148-174 MHz		5.0 kHz
Ham/Government	FM	406-450 MHz		12.5 kHz
UHF-Lo	FM	450-470	MHz	12.5 kHz
UHF-T (TV)	FM	470-512	MHz	12.5 kHz
UHF-Hi	FM	806-823.9375	MHz	12.5 kHz
UHF-Hi	FM	851- 868.9375MHz		12.5 kHz
UHF-Hi	FM	896.1125-956	MHz	12.5 kHz

FCC Notice

Your scanner might cause radio or TV interference even when it is operating properly. To determine if your scanner is causing the interference, turn off your scanner. If the interference goes away, your scanner was causing it. Try to elim- inate the interference by:

•Moving your scanner away from the receiver

•Connecting your scanner to an outlet that is on a different electrical circuit from the receiver

•Contacting your local Radio Shack store for help

If you cannot eliminate the interference, the FCC requires that you stop using your scanner.

Note: Mobile use of this scanner is unlawful or requires a permit in some areas. Check the laws in your area.

This device complies with Part 15 of FCC Rules. Operation is subject to the fol- lowing two conditions:

•This device may not cause harmful interference.

•This device must accept any interference received, including interference that may cause undesired operation.

4

Image 4

Radio Shack PRO-2040 owner manual FCC Notice

Contents

Fm Page 1 Wednesday, August 4, 1999 1112 AM Features Fm Page 3 Wednesday, August 4, 1999 1112 AM FCC Notice Contents Scanning Legally Connecting Power Using Standard AC PowerMemory Backup Preparation Using Vehicle Battery Power Telescoping Antenna Connecting AN AntennaOptional Outdoor Antenna Resetting the SCANNER’S Display Connecting AN EARPHONE/ HEADPHONES/ External Speaker Initializing Scanner Traffic Safety Listening Safely Understanding Your Scanner Look AT the Front Panel Programs a 2-second delay for the selected chan Stores frequencies into and accesses the 10 moniEnters the up or down direction in the search mode Turns the data skip feature on and off Look AT the Display Appears when you manually select a locked channel, or During a search hold when the frequency is storedAppears when you program a channel for a two-second Delay before scanning or when you listen to a channel Channel-Storage Banks Understanding the SCANNER’S MemoryMonitor Memories Turning on the SCANNER/SETTING the Volume and Squelch Operation Finding Birdie Frequencies Manually Storing Frequencies in Channels Searching for and Temporarily Storing Active Frequencies Limit Search Direct Search Search Skip Memory Listening to Monitor Memories Moving a Frequency from a Monitor Memory to a Channel Scanning the Stored Channels Manually Selecting a Channel Turning Channel-Storage Banks On and Off Listening to the Weather Band Using the 2-SECOND Delay Special FeaturesDesignating a Priority Channel Changing Scanning and Search Speeds Locking OUT ChannelsPRO-2040 has two scan and three search speeds Type Speed Detecting Data Signals Guide to Frequencies General Guide to ScanningGuide to the Action Bands Typical Band Usage Primary UsageHF Band 3.00-30.0 MHz VHF Band 30.00-300.0 MHz Band Allocation UHF Band Abbreviations High Frequency HF- 3 MHz-30 MHz Very High Frequency VHF- 30 MHz-300 MHz VHF-Hi Band 148-174 MHz Ultra High Frequency UHF- 300 MHz-3 GHz Low Band 450-470 MHz Frequency Conversion Trunked Systems Band Locally Assigned Troubleshooting Care and Maintenance Specifications DC 400 mA full volume unsquelched MHz and 450 kHzOhms Watts maximum Fm Page 43 Wednesday, August 4, 1999 1112 AM Radio Shack