Raypak 0090B 0135B Receiving Equipment, General Specifications, Specifications And Dimensions

1. RECEIVING EQUIPMENT

On receipt of your equipment it is suggested that you visually check for external damage to the carton. If the carton is damaged, it is suggested that a note be made on the Bill of Lading when signing for equipment. Remove the boiler from the carton and if it is damaged report the damage to the carrier immediately. Be sure that you receive the number of packages indicated on the Bill of Lading. Claims for shortages and damages must be filed with carrier by consignee.

Purchased parts are subject to replacement only under the manufacturer's warranty. Debits for defective replacement parts will not be accepted and defective parts will be replaced in kind only per our standard warranties.

When ordering parts, you must specify Model and Serial Number of boiler. When ordering under warranty conditions, you must also specify date of installation.

Raypak recommends that this manual be re- viewed thoroughly before installing your Raypak Boiler. If there are any questions which this manual does not answer, please contact your local Raypak representative.

2. GENERAL SPECIFICATIONS

The Raypak hydronic boilers are design certified by the American Gas Association, and tested under the requirements of the American National Standard, ANSI Z21.13. Each boiler has been constructed and pressure tested in accordance with the requirements of Section IV of the American Society of Mechanical Engineers Code, and factory fire tested.

The boilers are designed for indoor installation with

a built-in drafthood, and a built-in sub-base for combus-

tible flooring. Models are available with standing pilot,

or with intermittent ignition device (I.I.D.). The boilers

are equipped with the following components: water

circulation pump, pressure relief valve, temperature/

pressure gauge, adjustable high limit switch, drain

valve, fast response temperature sensor, 40 VA trans-

former, pump relay, vent thermal switch, flame roll-out

switch, and redundant combination gas valve for use

with either natural or propane gases. Two-staged gas

valve (50% firing on 1st stage) is standard on models

H-0090, H-0135 and H-0180.

Follow the installation instructions furnished with the vent damper package. The plug-in connector can also be used with power venters. Refer to the specific installation instructions supplied by the power vent manufacturer.

SPECIFICATIONS AND DIMENSIONS

PIPING

HEATING

NET

CONNECTIONS

K

INPUT

CAPACITY

I=B=R

WATER

GAS

VENT

MODEL

MBH

MBH

RATING

NPT.

NPT.

A

B

C

DIA.

H-0030

30

25

22

1"

1/2"

11"

5 3/4

5 1/2

4"

H-0042

42

35

30

1"

1/2"

11"

5 3/4

5 1/2

4"

H-0066

66

54

47

1"

1/2"

11"

5 3/4

5 3/4

5"

H-0090

90

74

64

1"

1/2"

11"

5 3/4

5 3/4

5"

H-0135

135

109

95

1 1/4"

1/2"

18"

6 1/4

6 1/4

6"

H-0180

180

148

129

1 1/4"

1/2"

18"

6 1/4

8.0

7"

B

AUTOMATIC

K

VENT DAMPER

(FIELD INSTALLED)

INLET

31/8

117/8

OUTLET

6

MIN

19

A

16 41/2

C

3/4 NPT PIPE TO DRAIN

The automatic ignition models and some standing

pilot models are provided with a plug-in connector that

is compatible with the Honeywell D80D vent damper.

331/4

THERMOSTAT CONN 31/4

(ELECTRICAL CONN ON OTHER SIDE)

18

Similar type vent dampers made by other manufactur-

ers, and design certified by a nationally-recognized

testing Agency, under the ANSI Z21.66 standards, may

also be used.

221/8

GAS

CONN

261/2

121/2

5

Fig. #8978.1

3