INSTALLATION

LEG AND BOTTOM SHIELD ASSEMBLY

These instructions apply to the steel leg, painted cast leg and the gold plated cast leg. It will be easier to attach the legs to the stove if it is tipped on its back (preferably on a soft surface to prevent scratching).

1)Remove the 4 bolts in the underside of the base and discard.

2)Put the bottom shield up against the bottom of the stove and loosely install the four sup- plied bolts and washers into the threaded holes in the four corners of the bottom the unit. Once the bolts are started, slip the leg under the washer and tighten the bolts.

3)Hook up wires to Burner ON/OFF switch and valve assembly as per pedestal assembly diagram (diagram 1).

4)Level the stove by adjusting the levelling bolts in the bottom of each leg.

OPTIONAL

OUTSIDE AIR

If needed, outside air for combustion can be brought in either through the bottom of the ped- estal or through the rear plate of the pedestal.

The pedestal cover plate must be installed when using outside combustion air. Loosen the 4 screws on the rear of the pedestal and slide the cover plate over them. Slide the plate to the left to center it and tighten down the 4 screws.

Outside Air Through

Pedestal Bottom

Once you have properly marked the position of your unit as outlined in "General Informa- tion" and "Clearances to Combustibles", cut a minimum 3 inch diameter hole though the fl oor directly under your pedestal base to the outside. Pipe fresh air into the pedestal area by using a minimum 3" duct pipe with a mesh grill at the outside termination.

Note: Blanking plate combustion air hole is 4" diameter.

Rear View

Outside Air Through

Pedestal Rear

Remove the blanking plate from the rear of the pedestal cover plate and bend the two tabs out 90 degrees. Pipe fresh air into the pedestal area by using a minimum 3" duct pipe with a mesh grill at the outside termination. Attach the pipe to the tabs with screws.

Note: The hole in the rear pedestal cover plate is 4" diameter.

IMPORTANT

Read all instructions carefully before starting the installation. Failure to follow these instruc- tions may create a fi re or other safety hazard, and will void the warranty. Be sure to check the venting and clearance to combustible require- ments. Consult your local building codes before beginning installation.

DRAFT HOOD

The heater has a draft hood built into its back. It must not be altered or obstructed, and the unit must be installed so that the draft hood is in the same atmospheric pressure zone as the combustion air inlet to the burner.

VENTING

This heater is a vented appliance and must be connected to a chimney/fl ue in accordance with installation codes.

Note: The rear cover plate is only attached when outside air is being used. Do not install it when using room air for combustion.

For your safety this heater is equipped with a ventsafetyswitch.Thisthermallyactuatedswitch is located within the draft hood and will detect either a blocked chimney or backdraft condition where the chimney fl ow has reversed and will react by shutting off the gas supply.

Note: Thespillswitchismanuallyresettable and comes from the factory in the open position. Before trying to start up the unit, make sure the red button on the spill switch is pushed in.

Venting Requirements

Four inch diameter vent is required. B-Vent, ClassAorMasonrywithalinerareallacceptable. Follow all venting manufacturer’s requirements and local building codes. For altitudes above 2000 ft. we recommend that a minimum fl ue height of 12 ft. is used.

Note: Proper sizing of gas vents is critical to proper operation of all gas stoves and fireplaces. Ensure that proper sizing tables or vent manufacturers instructions are followed.

Side View

Regency® CLASSIC C33-3 Freestanding Gas Stove

9

Page 8 Page 10
Page 9
Image 9
Regency C33-NG3, C33-LP3 installation manual Optional Outside AIR, Draft Hood, Venting
Page 8 Page 10

C33-NG3, C33-LP3 specifications

The Regency C33-NG3 and C33-LP3 are advanced gas fireplaces that reflect both elegance and functionality, making them ideal choices for those looking to enhance their living spaces. These models stand out in the market due to their exceptional design and innovative technology, catering to both natural gas and propane options.

One of the main features of the Regency C33-NG3 and C33-LP3 is their impressive heating capacity. Both models boast an efficiency rating that competently warms your space while maintaining eco-friendly operations. This makes them an attractive option for homeowners seeking a blend of luxury and sustainable heating solutions.

Both fireplace models are designed with a modern aesthetic, featuring a sleek front and expansive viewing area that allows the warm glow of flames to be the centerpiece of any room. With customizable trim options and the ability to add decorative media such as stones or glass, these fireplaces can be tailored to fit various interior designs. The contemporary linear design not only offers visual appeal but also maximizes the heat output, ensuring a cozy environment.

In terms of technology, the Regency C33-NG3 and C33-LP3 come equipped with an advanced electronic ignition system. This feature allows for easy lighting of the fireplace with the push of a button, eliminating the hassle associated with traditional ignition methods. Additionally, these models include a thermostatic control option, enabling users to maintain their desired temperature effortlessly.

The patented heat exchanger technology enhances the overall efficiency of both models, ensuring that the heat produced is directed into the room rather than being lost through the venting system. This innovative design contributes to a more efficient heating experience, making these fireplaces a cost-effective choice for consumers.

Safety is also a priority with the Regency C33-NG3 and C33-LP3. Both models incorporate safety barriers and advanced flame sensing technology, ensuring peace of mind during operation. The sleek glass front not only adds to the aesthetic but also keeps flames safely contained, making them suitable for families with children or pets.

In conclusion, the Regency C33-NG3 and C33-LP3 combine modern elegance with advanced heating technology. Their efficient heating capabilities, customizable designs, and user-friendly features make them standout choices for anyone looking to elevate their home’s ambiance while ensuring warmth and comfort.
Top Page Image Contents