Regency C33-LP3, C33-NG3 GAS Connection, System Data, High Elevation, GAS Pipe Pressure Testing

INSTALLATION

Installing into Existing

Woodstove Flue System

1)Clean existing chimney system.

2)Install stove pipe adapter

3)Install any reducers that may be needed to fi t 6" fl ue pipe adapter.

4)Run 4" fl ex liner into existing chimney.

5)Slip liner through 6" fl ue pipe and hook up to fl ue collar with screws.

Note: For ease of in- stallation, use a slip section when installing

with a ver- tical flue pipe.

GAS CONNECTION

The gas connection is a 3/8" NPT rigid pipe. The gas line can be rigid pipe or to make in- stallation easier, use a listed fl exible connector and/or copper pipe if allowed by local codes. For minimum and maximum supply pressure see the System Data table below.

Note: During any pressure testing of the gas supply piping system that ex- ceeds test pressures of 1/2 psig, this appliance and its individual shut-off valve must be disconnected from the piping system. If test pressures equaltoorlessthan1/2psigareused then this appliance must be isolated from the piping system by closing its individual manual shut-off valve during the testing.

Output capacity:

The efficiency rating of the appliance is a product thermal efficiency rating determined under continuous operating conditions and was determined independently of any installed system.

SYSTEM DATA

(For 0 to 2,000 feet altitude)

Orifice Sizes:
Burner	Natural Gas	#36
Burner	Propane	#52
Max. Input Rating
Natural Gas	33,000 Btu/h
Propane	33,000 Btu/h
Min. Input Rating
Natural Gas	17,000 Btu/h
Propane	17,000 Btu/h
Output Capacity with blower Off
Natural Gas	23,200 Btu/h
Propane	23,100 Btu/h
Output Capacity with blower On
Natural Gas	24,600 Btu/h
Propane	24,420 Btu/h
Supply Pressure
Natural Gas	min.	5.0" w.c
	max.	8.0" w.c.
Propane	min.	12.0" w.c.
	max.	13.0" w.c.
Manifold Pressure High
Natural Gas	3.8" +/- 0.2" w.c.
Propane	11" +/- 0.2" w.c.
Manifold Pressure Low
Natural Gas	1.1" +/- 0.2" w.c.
Propane	2.9" +/- 0.2" w.c.

Electrical: 120V, 1.13A, 60 Hz.

Circulation Fan: (optional) 2 speed 75/125 CFM.

Log Set: Ceramic fi ber, 4 per set.

HIGH ELEVATION

This unit is approved in Canada for altitude 0 to 4500 ft. (CAN1 2.17-M90) with the orifi ce supplied.

SYSTEM DATA

(For 2,000 to 4,500 feet altitude)

Orifice Sizes:
Burner	Natural Gas	#38
Max. Input Rating
Natural Gas	29,000	Btu/h
Min. Input Rating
Natural Gas	15,300	Btu/h
Output Capacity with blower Off
Natural Gas	20,400	Btu/h
Output Capacity with blower On
Natural Gas	21,600	Btu/h

GAS PIPE

PRESSURE TESTING

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pressures over 1/2 psig (14" w.c.).

Themanifoldpressureiscontrolledbyaregulator built into the gas control, and should be checked at the pressure test point.

Note: To properly check gas pressure, both inlet and manifold pressures should be checked using the valve pressure ports on the valve.

1)Make sure the valve is in the "OFF" posi- tion.

2)Loosen the "IN" and/or "OUT" pressure tap(s), turning counterclockwise with a 1/8" wide fl at screwdriver.

3)Attach manometer to "IN" and/or "OUT" pressure tap(s) using a 5/16" ID hose.

4)Light the pilot and turn the valve to "ON" position.

5)The pressure check should be carried out with the unit burning and the setting should be within the limits specifi ed on the safety label.

6)When fi nished reading manometer, turn off the gas valve, disconnect the hose and tighten the screw (clockwise) with a 1/8" fl at screwdriver. Screw should be snug, but do not over tighten.

10 Regency® CLASSIC C33-3 Freestanding Gas Stove