Manuals / RF-Link Technology / Baby / Model Vehicle

RF-Link Technology RFL NCM, Network Communications Module manual Nms

Models: Network Communications Module RFL NCM

1 52

Download 52 pages 11.34 Kb

Page 16

Table 2. Application Modes And Bus Settings

NMS	Transmit on A	Transmit on B	Application
Application	Receive on B	Receive on A
Mode	(SW2-6)	(SW2-7)
(SW7-4,
SW7-5 &
SW7-6)
Broadcast	enabled	disabled	The NCM mode will be Terminal broadcast or DI-A broadcast

	disabled	enabled	The NCM mode will be DI-B broadcast

	enabled	enabled	The NCM mode will be D&I broadcast

	disabled	disabled	(Not a valid setting. The NCM module is disabled)

NMS	enabled	disabled	The NCM mode will be Terminal NMS or DI-A NMS

	disabled	enabled	The NCM mode will be DI-B NMS

	enabled	enabled	The NCM mode will be D&I NMS

	disabled	disabled	(Not a valid setting. The NCM module is disabled)

Master	enabled	disabled	The NCM mode will be Terminal Master or DI-A Master

	disabled	enabled	The NCM mode will be DI-B Master

	enabled	enabled	The NCM mode will be D&I Master

	disabled	disabled	(Not a valid setting. The NCM module is disabled)

D&I Slave	enabled	disabled	The NCM mode will be D&I Slave and the Master NCM node is in
			the A direction.
	disabled	enabled	The NCM mode will be D&I Slave and the Master NCM node is in
			the B direction.
	enabled	enabled	(Not a valid setting. The NCM module is disabled)
	disabled	disabled	(Not a valid setting. The NCM module is disabled)
D&I End	enabled	disabled	The NCM mode will be Terminal End Slave or DI-A End Slave
	disabled	enabled	The NCM mode will be DI-B End Slave
	enabled	enabled	(Not a valid setting. The NCM module is disabled)
	disabled	disabled	(Not a valid setting. The NCM module is disabled)

Note: enabled = DOWN, disabled = UP

RFL NCM		RFL Electronics Inc.
November 6, 2007	16	(973) 334-3100

Image 16

RF-Link Technology RFL NCM, Network Communications Module manual Nms

Contents

Description RFL NCMRFL NCM Specifications NMS Mode Ascii Character Addressing FormatInstallation RFL NCM MA-402I Module adapter, connector pinouts MA-485 Module adapter, jumper functions and TB1 pinouts MA-490 RFL NCM Front Panel View of RFL NCM, Network Communications Module Typical network example with all nodes having an NCM module At node 3, SW7 is set as follows Controls and indicators, RFL NCM Module Name/Description Function RFL NCM PRA Actel probe a NMS NMSDown SW2-3 SW2-4 Do not move SW10-4 Block diagram, RFL NCM module Functional DescriptionSystem Overview NCM Backplane and Power Connections TX Input PortsRX Output Ports Logic Array Actel DesignSCB Module Application Modes and InterfacesUart Receive Section Uart Transmit Section T1 Transmit ModuleT1 Receive Module Rogue ControlLOOP-BACKS Baud and Clock GeneratorTesting Power indicator should be litService LED should be illuminated green Test Equipment RequiredDS1 Power indicator should be lit DS1-B Equip OUT RXA LED should be illuminated red CH1 DS1-B Equip OUT CH2 Remote Control Using NMS NCM General Configurations and Status window for NodeModule Enable E1 SignalingTime Slot ModeTypical 3-node network using MA-485s 1 RS-485 port Bus a & Bus B Rogue DetectionNCM Address Configurations and Status window for Node Local CM AddressCM Address Passing Data Bits Baud RateParity Port 2 Enable TroubleshootingLoopback Channel Card 3, Type 117 Under Remote Control Svce = on Remote Control Using SCL CommandsCodes Multiplexer Addresscard ADDRESSSETP1 = B00000011 Srvc = on Srvc = OFFBUS a Setting BUS B SettingCAS Setting Timeslot SelectionPort Loopback Settings Baud SettingsParity Settings Word Length SettingsCM Address Pass Settings NMS Mode onlyApplication Mode SettingsCodes MUX Type & Configuration Status Type IDPort 1 Availability Port 2 AvailabilityApplication Configuration Status CM Addressing SupportPort 1 Application Status Port 2 Application StatusRXA Remote CM Address Current Actel REVPort 1 INPUT/OUTPUT Status Port 2 INPUT/OUTPUT StatusTXA/RXB Status for T1/E1 TXB/RXA Status for T1/E1Powerville Road