The content on this page is intended for use by qualified
installation/service personnel ONLY.
WARNING: Improper adjustment, alteration, | ! DANGER: Hotter water increases |
service or maintenance can cause property damage, | the potential for Hot Water SCALDS. |
personal injury, or death. |
|
Temperature Setting DIP Switch Adjustment
Required adjustment for up to 180°F (82°C) water temperature settings
!WARNING: Refer to scald potential warnings on page 4 before making adjustment. Changing this setting is done at your own risk.
DO NOT alter the #4 DIP Switch if the setting of up to 180°F (82°C) is not required.
Follow the instructions below if it is determined that a setting of up to 180°F (82°C) is required.
●Turn off remote control. Turn off the gas and water shutoff valves.
●Remove the front cover.
●Find the DIP Switch #4 located at the top left hand side of the PCB. (See illustration to the right for DIP Switch location)
●Change the DIP Switch #4 setting to the “ON” position. DO NOT alter any other DIP Switch. The LED on the PCB is flashing. At the same time, the display of the Main Remote Control starts to flash.
●Press the “Max” button on the left hand side of the PCB for more than 1 second. The LED on the PCB starts illuminating continuously. At the same time, the display of the Main Remote Control is on continuously.
●Change the DIP Switch #4 setting back to the “OFF” position. DO NOT alter any other DIP Switch. The LED on the PCB will stop illuminating. At the same time, the display of the Main Remote Control will turn off.
Time/Temperature Relationship in Scalds
Water Temperature |
|
|
| Time To Produce a Seroius Burn | ||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
120°F (49°C) |
|
|
|
|
|
| More than 5 minutes | |||||||||||||||||
125°F (52°C) |
|
|
|
|
|
|
| 1 ½ to 2 minutes | ||||||||||||||||
130°F (54°C) |
|
|
|
|
|
|
| About 30 seconds | ||||||||||||||||
135°F (57°C) |
|
|
|
|
|
|
| About 10 seconds | ||||||||||||||||
140°F (60°C) |
|
|
|
|
|
| Less than 5 seconds | |||||||||||||||||
145°F (63°C) |
|
|
|
|
|
| Less than 3 seconds | |||||||||||||||||
150°F (66°C) |
|
|
|
|
|
|
| About 1 ½ seconds | ||||||||||||||||
155°F (68°C) |
|
|
|
|
|
|
|
| About 1 second | |||||||||||||||
Table courtesy of Shriners Burn Institute | ||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
| ON | ||||||||||||||||
DIP1 |
| ON |
|
|
|
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 1 | 2 | 3 |
| 4 |
|
| OFF | ||||||||||||||||
1 | 2 | 3 |
| 4 |
|
| ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Location of DIP Switches on PC Board.
●Attach the unit’s front cover.
●Turn on the remote control, gas and water shutoff valves.
●Check and ensure safe operation and performance of the water heater.
See steps below to LIMIT maximum water temperature setting to 120 (49°C). Follow first four bullets points listed above, then continue as listed below:
●Press the “Min.” button on the left hand side of the PCB for more than 1 second. The LED on the PCB starts illuminating continuously. At the same time, the display of the Main Remote Control is on continuously.
●Change the DIP Switch #4 setting back to the “OFF” position. DO NOT alter any other DIP Switch. The LED on the PCB will stop flashing. At the same time, the display of the Main Remote Control turn off.
●Attach the unit’s front cover.
● Turn on the remote control, gas and water shutoff valves. |
|
| “Max” | |||||
● Check and ensure safe operation and |
|
| Button | |||||
|
|
|
|
| LED | |||
performance of the water heater. |
|
|
|
|
| |||
|
|
|
|
|
| |||
| SW1 | SW2 | ||||||
|
|
|
|
|
|
|
|
|
“Min.” | SW3 | DIP1 |
|
| ON |
Button |
|
|
|
| OFF |
| 1 | 2 | 3 | 4 |
DIP
Switches
ON |
1 2 3 4
As set from factory
ON |
1 2 3 4
Setting during adjustment
to DIP Switch #4 for temperature.
ON |
1 2 3 4
Setting after adjustment
to DIP Switch #4 for temperature.
35
