RIDGID K6200 manual Machine Assembly, Cables and Flexible Trap Leaders

K-6200 Drain Cleaning Machine

Cables and Flexible Trap Leaders

	Catalog	Model
	No.	No.	Description
	92460	C-25	25′ I.C. Cable (7,6m)
	92465	C-26	50′ I.C. Cable (15,2m)
	92470	C-27	75′ I.C. Cable (22,9m)
5/8″ (16mm)	43647	C-24	100′ I.C. Cable (30,5m)
	32737	C-27HC	75′ Hollow-Core (22,9m)
5/8″ (16mm)	58192	C-24HC	100′ Hollow-Core (30,5m)
	95762	C-25 IW	25′ I.W. Cable (7,6m)
	95757	C-26 IW	50′ I.W. Cable (15,2m)
5/8″ IW (16mm)	95752	C-27 IW	75′ I.W. Cable (22,9m)
	95747	C-24 IW	100′ I.W. Cable (30,5m)
	92555	T-458	5/8″ x 2′ Leader
	44122	—	5/8″ Pigtail

Tools and Replacement Blades — Fits C-24, C-25, C-26, C-27,C-24 IW, C25 IW, C-26 IW, C-27 IW, C-24HC, C-27HC

Catalog	Model			Replacement
No.	No.		Description	Blade(s)		Holder*
92485	T-403		P-Trap Cutter, 3″	92835		92900
92490	T-404		P-Trap Cutter, 31/2″	92840		92900
92495	T-406		Spear Blade	92850		92915
92500	T-407		Retrieving Auger	—		—
92505	T-408		Sawtooth Cutter	92890		92915
51762	T-409		H-D Bulb Auger	—		—
92510	T-411		Double Cutter, 2″	92815		92905
92515	T-412		Double Cutter, 21/2″	92820		92905
92520	T-413		Double Cutter, 3″	92825		92910
92525	T-414		Double Cutter, 4″	92830		92910
92530	T-416		Double Cutter, 6″	92855		92910
92535	T-432		3-Blade Cutter, 2″	92860		92895
92540	T-433		3-Blade Cutter, 3″	92865		92895
92545	T-434		3-Blade Cutter, 4″	92870		92895
92550	T-436		3-Blade Cutter, 6″	92875		92895
		Blade			Fastener*
Blade
Holder

Coupling*

* Identifies components included with holder

Figure 2 – Tool Assembly

Machine Assembly

WARNING

To prevent serious injury, proper assembly of the Drain Cleaner is required. The following procedures should be followed:

Instructions For Installing Handles

Remove the two (2) screws from handle. Loosen two (2) “T” handles and slide handle into the frame (Figure 5). Replace the two screws in the handle to prevent it slid- ing out of the frame. Adjust the handle to the desired height and firmly tighten the “T” handles to lock the handle in place.

Instructions For Installing Cable

CAUTION Do not remove bands or staples from cable shipping carton. Cable is under tension and will whip, causing injury.

Retrieve end of cable through the center hole of carton and remove enough cable to connect with drum pigtail. Connect to pigtail by sliding cable couplings together and turning screwdriver slot in coupler 180°. Couplings are in locked position when hash mark is on opposite side of screwdriver slot as shown in Figure 3. Feed cable into drum.

QUICK-CONNECT CABLE & TOOLS

Rotate pin one-half turn in either direction to

quickly add cable or tools.

	Hash Mark
Screwdriver Slot
	(Locked position)

LOCKED

Hash mark CLOSED aligned with L stamped on coupling.

Hash Mark

(Un-locked position) Screwdriver Slot

UNLOCKED

Hash mark OPEN aligned opposite L stamped on coupling.

Coupling features stainless steel pin and spring: eliminates need for

punches, stands, or expansion pins.

Figure 3 – Disconnecting/Connecting Cable to Pigtail or Tool

Ridge Tool Company 5