OPERATION

Slowly lower the blade into and through the workpiece.

Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops blade from turning before removing the workpiece from miter table.

TO Compound Miter Cut

A compound miter cut is a cut made using a miter angle and a bevel angle at the same time. This type of cut is used to make picture frames, cut molding, make boxes with sloping sides, and for certain roof framing cuts.

To make this type of cut the control arm on the miter table must be rotated to the correct angle and the saw arm must be tilted to the correct bevel angle. Care should always be taken when making compound miter setups due to the interaction of the two angle settings.

Adjustments of miter and bevel settings are interdependent with one another. Each time you adjust the miter setting you change the effect of the bevel setting. Also, each time you adjust the bevel setting you change the effect of the miter setting.

It may take several settings to obtain the desired cut. The first angle setting should be checked after setting the second angle, since adjusting the second angle affects the first.

Once the two correct settings for a particular cut have been obtained, always make a test cut in scrap material before making a finish cut in good material.

Pull out the lock pin and lift saw arm to its full height.

Loosen the miter lock handle. Rotate the miter lock han- dle approximately one-half turn to the left to loosen.

Press the miter lock plate down with your thumb and hold.

Rotate the miter table until the pointer aligns with the desired angle on the miter scale.

Release the miter lock plate.

NOTE: You can quickly locate 0°, 15°, 22.5°, 31.6°, and 45° left or right by releasing the miter lock plate as you rotate the control arm. The miter lock plate will seat itself in one of the positive stop notches, located in the miter table base.

Tighten the miter lock handle securely.

Loosen the bevel lock knob and move the saw arm to the left to the desired bevel angle.

Bevel angles can be set from -2˚ to 47˚.

Once the saw arm has been set at the desired angle, securely tighten the bevel lock knob.

Compound

Miter Cut

WORK CLAMP

Fig. 30

 

Make a test cut in scrap material.

Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board could collapse on the blade at the end of the cut, jamming the blade. See Figures 34 - 35.

When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table. See Figure 32.

25

Page 24 Page 26
Page 25
Image 25
RIDGID MS1250LZA manual To Compound Miter Cut, Work Clamp
Page 24 Page 26

MS1250LZA specifications

The RIDGID MS1250LZA is a versatile and robust miter saw designed for professionals and DIY enthusiasts alike. This powerful tool is engineered to deliver precision cutting for a wide range of materials, including wood, plastic, and light metals, making it an ideal choice for carpenters, contractors, and hobbyists.

One of the standout features of the MS1250LZA is its impressive 15-amp motor, which provides ample power to handle tough cutting tasks with ease. The motor is capable of reaching up to 5000 RPM, ensuring clean and accurate cuts every time. Whether you are making crosscuts, miters, or bevel cuts, this saw can handle it all with precision and efficiency.

The MS1250LZA incorporates a dual bevel design, allowing for both left and right angles of bevel cuts. This flexibility enhances the saw's usability, enabling users to create compound cuts without needing to flip the workpiece, which saves time and increases accuracy. The intuitive bevel adjustment lever allows for quick and straightforward adjustments, ensuring that you can easily switch between angles as needed.

Another significant technological advancement in the MS1250LZA is the laser guide system. This feature projects a clear, precise line on the cutting surface, providing enhanced visibility and accuracy. Users can easily line up their cuts without the guesswork, making it especially beneficial for intricate projects or when working with small pieces.

The saw's sliding feature is also noteworthy, as it allows for larger cuts with ease. The sliding arm can handle wider materials, making it perfect for framing lumber, larger boards, or even plywood sheets. Additionally, the positive stops on the miter table provide easy access to commonly used angles, streamlining the workflow for repetitive cuts.

Safety is paramount in any power tool, and the RIDGID MS1250LZA includes several safety features that protect both the user and the workpiece. The electric brake stops the blade quickly after the trigger is released, minimizing the risk of accidents. A transparent blade guard allows users to see the cutting area while keeping hands and fingers safe from the blade.

In terms of portability, the MS1250LZA is relatively lightweight and features a sturdy carrying handle, making it easy to transport between job sites. The durable construction ensures that it can withstand the rigors of professional use while delivering reliable performance over time.

Overall, the RIDGID MS1250LZA miter saw presents an impressive combination of power, flexibility, and safety features, making it an indispensable tool for any serious woodworking or construction project. With its user-friendly design and high-performance capabilities, it is sure to enhance the productivity and efficiency of its users.
Top Page Image Contents