Manuals / RIDGID / Lawn and Garden / Pressure Washer

RIDGID RD80763 assembling the trigger handle, attaching the auxiliary handle, Spray Wand, Collar

Models: RD80763

1 28

Download 28 pages 40.48 Kb

Page 11

assembling the trigger handle

ASSEMBLY

WARNING:

Make sure the nozzle and hose connections are secure before starting the machine. A non-secured accessory could become a projectile if not properly installed which could result in serious injury.

assembling the trigger handle

See Figure 7.

TRIGGER

HANDLE auxiliary

HANDLE

nPlace the threaded end of the spray wand in the connec- tor on the end of the trigger handle.

nTurn the connector clockwise until it stops. This secures the wand in place.

nWhen not in use, remove the spray wand from the trigger handle by turning the connector counterclockwise. Store the unassembled spray wand in the spray wand storage area.

attaching the auxiliary handle

See Figure 7.

n Place the threaded stud on the end of the auxiliary handle

into the hole in the trigger handle as shown below. Turn

clockwise to tighten.

CONNECTOR

high

PRESSURE HOSE

SPRAY

WAND

Fig. 7

NOTE: You can install the handle on either the left or right

side of the spray wand, depending on operator prefer-

ence. The handle must always be used to prevent loss

of control and possible serious injury.

n To switch sides, loosen the auxiliary handle and rotate to

the opposite side. Tighten securely before use.

connecting high pressure hose to

TRIGGER HANDLE

See Figure 8.

nPull back and hold the collar on the high pressure hose. In- sert the inlet coupler on the trigger handle into the collar.

nRelease the collar and push until it locks into place. Pull on the hose to be certain it is properly secured.

attaching INJECTION hose

See Figure 9.

Before detergent can be used with this machine, the injection hose must be attached.

nPush the open end of the clear injection hose securely over the fitting as shown in figure 9.

nPlace the filtered end of the injection hose in the bottle of detergent.

COLLAR

inlet
coupler	Fig. 8

Injection hose

Fig. 9

11

Image 11

RIDGID RD80763 assembling the trigger handle, attaching the auxiliary handle, attaching INJECTION hose, Spray Wand, Collar

Contents

SAVE THIS MANUAL FOR FUTURE REFERENCE OPERATOR’S MANUALGASOLINE pressure washer RD80763/RD8096413-17 TABLE OF CONTENTSINTRODUCTION 8-13 Exercise caution to avoid slipping or falling IMPORTANT SAFETY INSTRUCTIONS Follow the maintenance instructions specified in this manual READ ALL INSTRUCTIONS If the fuel tank has to be drained, do this outdoors Specific SAFETY RULES Never pick up or carry a machine while the engine is running  Keep the engine away from flammables and other hazardous materialsDESIGNATION/EXPLANATION SYMBOLSSYMBOL NAMEMEANING SERVICESIGNAL DANGERDual Power FEATURESPRODUCT SPECIFICATIONS cleaningKNOW YOUR pressure washer ASSEMBLYengine switch Dual Power Soap NozzleASSEMBLY attaching the rear panelhandle torx screw rear panel AXLE WASHER wheel hitch pinREMOVE the LABEL attaching the wheel assembly and SUPPORT FOOTattaching the trigger handle rest RAISING AND LOWERING the handleattaching the auxiliary handle connecting high pressure hose to TRIGGER HANDLECONNECTOR high PRESSURE HOSE assembling the trigger handleOIL CAP / adding oil to the engineadding gasoline to THE FUEL tank FUNNELWARNING WARNING connecting the garden hose to the pressure washerconnecting the high pressure hose to the pump OPERATIONstarting and stopping the pressure washer To stop the engine using the engine switchENGINE SWITCH choke closed - AON Throttle fuel valve RECOIL STARTER ApplicationsTo engage the lock out using the spray wand triggerUSING the NOZZLES OperationFor short range detergent application washing with detergentSee Figures 20 For long range detergent applicationSee Figure rinsing with the pressure washerMOVING the pressure washer OperationAIR FILTER COVER AIR FILTER MAINTENANCEGENERAL MAINTENANCE cleaning the air filterchecking a fouled spark plug nozzle maintenancecleaning tool changing the OILTrigger and auxiliary handles pump maintenanceSTORING the pressure washer preparing for use after storageCause troubleshootingProblem SolutionPage OBTAINING WARRANTY SERVICE WARRANTYFEDERAL EMISSIONS COMPONENT DEFECT WARRANTY EMISSION COMPONENT DEFECT WARRANTY PERIODGENERAL EMISSIONS WARRANTY COVERAGE California Only CALIFORNIA EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONS WARRANTYDescriptive Term WARRANTYHIGH ALTITUDE ENGINE OPERATION AIR INDEXRely on Subaru Robin Reliability LIMITED 3 YEAR ENGINE WARRANTY FOR RIDGID PRESSURE WASHERLimited Manufacturer’s Warranty from Subaru Robin WARRANTY PERIODSHOW TO OBTAIN SERVICE RIDGID PRESSURE WASHER 3 YEAR LIMITED WARRANTYWHAT IS COVERED UNDER THE 3 YEAR LIMITED WARRANTY WHAT IS NOT COVEREDRD80763 / RD80964 Customer Service InformationRD80763 / RD80964 Model No