Manuals / Roberts Gorden / Household Appliance / Gas Heater

Roberts Gorden Linear Heater manual Danger, Replacement Parts

Models: Linear Heater

1 50

Download 50 pages 4.35 Kb

Page 41

SECTION 13: REPLACEMENT PARTS

SECTION 13: REPLACEMENT PARTS

SECTION 13: REPLACEMENT PARTS

DANGER

WARNING

Electrical Shock Hazard Explosion Hazard Fire Hazard Carbon Monoxide Hazard

Use only genuine ROBERTS GORDON® replacement parts per this installation, operation and service manual.

Failure to follow these instructions can result in death, electric shock, injury or property damage.

55

Image 41

Roberts Gorden Linear Heater manual Danger, Replacement Parts

Contents

FIGURE 15 Linear Heater Assembly Overview FIGURE 16 Linear Heater Layout Overview Tubing requires a downward slope of 1/2 13 mm Step 6.1 Burner Tube Installationper 20 6 m away from burner S-Hook Hanger Burner Tube 7 6 ± 229 cm ± 25 cmStep 6.3 Coupling and Tube Assembly Step 6.2 Tube Clamp Package Installation± 2 5 cm Step 6.3.1 Coupling and Tube Assembly ContinuedStep 6.3.2 Coupling and Tube Assembly Continued Step 6.4 Turbulator Installation Reflector must not touch tube Step 6.5 Reflector InstallationFire Hazard The pictorial drawings of the heater construction in Section 6 are schematic only and provide a general guideline of where hangers, reflector supports and U-clipsare to be installed SECTION 6 HEATER INSTALLATION Step 6.6 Burner InstallationExtra chain min 12 30 cm Burner7.1 U-TubeConfiguration SECTION 7 OPTIONAL HEATER ACCESSORIESCut/Pinch Hazard Edges are sharpU-tube,Standard FIGURE 18 U-TubeHeater Assembly OverviewU-tube U-tubeFIGURE 19 U-TubeHeater Layout Overview FIGURE 20 U-TubeLayout Overview Continued Step 7.2.3 Reflector Joint Installation Step 7.2.2 Elbow InstallationStep 7.2.4 Reflector Joint Installation Reflector Reflector JointSECTION 7 OPTIONAL HEATER ACCESSORIES Install reflectorStep 7.2.5 Reflector Joint Detail FIGURE 21 Reflector Joint Detail7.3 Reflector Side Extension Step 7.3.1 Bracket InstallationStep 7.3.2 Side Reflector Installation Step 7.4.1 Shield Support Strap Assembly 7.4Lower Clearance Shield InstallationSECTION 7 OPTIONAL HEATER ACCESSORIES DescriptionStep 7.5.2 Frame Shield Installation Step 7.6.3 Grille Installation Step 7.6.2 Grille End Cap InstallationCarbon Monoxide Hazard SECTION 8 VENTINGCut/Pinch Hazard Edges are sharp8.3 Horizontal Venting 8.2 Unvented Operation8.4 Vertical Venting 8.5 Unvented Operation Tube Termination8.8 Vertical Ventilation 4 10 cm Pipe 8.7 Horizontal Ventilation 4 10 cm PipeSIDE VIEW Combustible orHeaters must be of the same BTU output 8.9 Common Side Wall VentingRequirements Requirements 8.10 Common Vertical VentingHeaters must be of the same BTU output 8.11.1 Length Requirements 8.11 Outside Combustion Air SupplyRequirements RequirementsSECTION 9 GAS PIPING Gas hose can crack when twistedFire Hazard Gas hose moves during normal operationINCORRECT POSITIONS WRONG INSTALLATION when attaching gas hoseFIGURE 23 Gas Connection with Flexible Gas Hose CORRECT POSITIONSSECTION 10 WIRING DANGERDisconnect electric before service or maintenance 10.1 Line Voltage Thermostat Wiring10.2 Low Voltage Thermostat Wiring Pressure Switch 10.3 Internal WiringDSI Ignition Module BLUE ElectrodeConnect wires together with heater before service SECTION 11 OPERATION AND MAINTENANCEbefore service or during installationFor best performance, the gas, electrical, thermostat connections, tubing, venting, suspensions and overall heater condition should be inspected thoroughly Installation Code and Annual Inspections 11.5 Maintenance ChecklistThe Vicinity of the Heater See Page 4, SectionElectrode Burner Cup and OrificeThermostat See Page 43, SectionDisconnect electric before service or maintenance SECTION 12 TROUBLESHOOTINGheater before service before service or12.1 Troubleshooting Flow ChartSECTION 12 TROUBLESHOOTING Top View of Heater 12.2 Manifold Gas Pressure SettingNatural Propane DANGER SECTION 13 REPLACEMENT PARTSTOP VIEW REAR VIEWPart Number Description14.1 Material Specifications 14.1.1 Reflectors SECTION 14 GENERAL SPECIFICATIONS14.2 Heater Specifications 14.2.1 Ignition DIMENSIONSROBERTS-GORDONLLC WILL PAY FOR WARRANTY IS VOID IFROBERTS-GORDONLLC WILL NOT PAY FOR LIMITATIONS ON AUTHORITY OF REPRESENTATIVESPage About the Installer OWNER WARRANTY REGISTRATION CARDPurchased From if different than installer Type of Installation check onePage Page clearance Maintainthe side clearance below