FIGURE 15 Linear Heater Assembly Overview
FIGURE 16 Linear Heater Layout Overview
Burner Tube 7 6 ± 229 cm ± 25 cm
Step 6.1 Burner Tube Installation
Tubing requires a downward slope of 1/2 13 mm
per 20 6 m away from burner S-Hook Hanger
Step 6.3 Coupling and Tube Assembly
Step 6.2 Tube Clamp Package Installation
Step 6.3.1 Coupling and Tube Assembly Continued
Step 6.3.2 Coupling and Tube Assembly Continued
± 2 5 cm
Step 6.4 Turbulator Installation
Step 6.5 Reflector Installation
Fire Hazard
Reflector must not touch tube
The pictorial drawings of the heater construction in Section 6 are schematic only and provide a general guideline of where hangers, reflector supports and U-clipsare to be installed
Burner
Step 6.6 Burner Installation
SECTION 6 HEATER INSTALLATION
Extra chain min 12 30 cm
Edges are sharp
SECTION 7 OPTIONAL HEATER ACCESSORIES
7.1 U-TubeConfiguration
Cut/Pinch Hazard
U-tube
FIGURE 18 U-TubeHeater Assembly Overview
U-tube,Standard
U-tube
FIGURE 19 U-TubeHeater Layout Overview
FIGURE 20 U-TubeLayout Overview Continued
Reflector Reflector Joint
Step 7.2.2 Elbow Installation
Step 7.2.3 Reflector Joint Installation
Step 7.2.4 Reflector Joint Installation
FIGURE 21 Reflector Joint Detail
Install reflector
SECTION 7 OPTIONAL HEATER ACCESSORIES
Step 7.2.5 Reflector Joint Detail
Step 7.3.1 Bracket Installation
Step 7.3.2 Side Reflector Installation
7.3 Reflector Side Extension
Description
7.4Lower Clearance Shield Installation
Step 7.4.1 Shield Support Strap Assembly
SECTION 7 OPTIONAL HEATER ACCESSORIES
Step 7.5.2 Frame Shield Installation
Step 7.6.3 Grille Installation
Step 7.6.2 Grille End Cap Installation
Edges are sharp
SECTION 8 VENTING
Carbon Monoxide Hazard
Cut/Pinch Hazard
8.5 Unvented Operation Tube Termination
8.2 Unvented Operation
8.3 Horizontal Venting
8.4 Vertical Venting
Combustible or
8.7 Horizontal Ventilation 4 10 cm Pipe
8.8 Vertical Ventilation 4 10 cm Pipe
SIDE VIEW
8.9 Common Side Wall Venting
Requirements
Heaters must be of the same BTU output
8.10 Common Vertical Venting
Heaters must be of the same BTU output
Requirements
8.11.1 Length Requirements
8.11 Outside Combustion Air Supply
Requirements
Requirements
Gas hose moves during normal operation
Gas hose can crack when twisted
SECTION 9 GAS PIPING
Fire Hazard
CORRECT POSITIONS
when attaching gas hose
INCORRECT POSITIONS WRONG INSTALLATION
FIGURE 23 Gas Connection with Flexible Gas Hose
10.1 Line Voltage Thermostat Wiring
DANGER
SECTION 10 WIRING
Disconnect electric before service or maintenance
10.2 Low Voltage Thermostat Wiring
Electrode
10.3 Internal Wiring
Pressure Switch
DSI Ignition Module BLUE
Connect wires together with
during installation
SECTION 11 OPERATION AND MAINTENANCE
heater before service
before service or
For best performance, the gas, electrical, thermostat connections, tubing, venting, suspensions and overall heater condition should be inspected thoroughly
See Page 4, Section
11.5 Maintenance Checklist
Installation Code and Annual Inspections
The Vicinity of the Heater
See Page 43, Section
Burner Cup and Orifice
Electrode
Thermostat
before service or
SECTION 12 TROUBLESHOOTING
Disconnect electric before service or maintenance
heater before service
12.1
Troubleshooting Flow Chart
SECTION 12 TROUBLESHOOTING
12.2 Manifold Gas Pressure Setting
Natural Propane
Top View of Heater
DANGER
SECTION 13 REPLACEMENT PARTS
TOP VIEW
REAR VIEW
Part Number
Description
DIMENSIONS
SECTION 14 GENERAL SPECIFICATIONS
14.1 Material Specifications 14.1.1 Reflectors
14.2 Heater Specifications 14.2.1 Ignition
LIMITATIONS ON AUTHORITY OF REPRESENTATIVES
WARRANTY IS VOID IF
ROBERTS-GORDONLLC WILL PAY FOR
ROBERTS-GORDONLLC WILL NOT PAY FOR
Page
Type of Installation check one
OWNER WARRANTY REGISTRATION CARD
About the Installer
Purchased From if different than installer
Page
Page
clearance below
Maintain
clearance
the side
