Manuals / Roberts Gorden / Household Appliance / Gas Heater

Roberts Gorden Linear Heater manual 6 Burner Installation, Extra chain min 12 30 cm, Gasket, Lock

Models: Linear Heater

1 50

Download 50 pages 4.35 Kb

Page 9

Step 6.6 Burner Installation

SECTION 6: HEATER INSTALLATION

Step 6.6 Burner Installation

Extra chain min.

12" (30 cm)

	Burner	Gasket
		Gasket
		Lock
		Washer
Description	Part Number
Bolt	94273914
Burner	071XXXXX
Lock Washer	96411600
Gasket	02568200

S-hook

Burner Tube

Bolt (Torque 120 13.56 Nm)

23

Image 9

Roberts Gorden Linear Heater manual 6 Burner Installation, Extra chain min 12 30 cm, Gasket, Lock, Description, Part Number

Contents

FIGURE 15 Linear Heater Assembly Overview FIGURE 16 Linear Heater Layout Overview Tubing requires a downward slope of 1/2 13 mm Step 6.1 Burner Tube Installationper 20 6 m away from burner S-Hook Hanger Burner Tube 7 6 ± 229 cm ± 25 cmStep 6.3 Coupling and Tube Assembly Step 6.2 Tube Clamp Package InstallationStep 6.3.1 Coupling and Tube Assembly Continued Step 6.3.2 Coupling and Tube Assembly Continued± 2 5 cm Step 6.4 Turbulator Installation Step 6.5 Reflector Installation Fire HazardReflector must not touch tube The pictorial drawings of the heater construction in Section 6 are schematic only and provide a general guideline of where hangers, reflector supports and U-clipsare to be installed SECTION 6 HEATER INSTALLATION Step 6.6 Burner InstallationExtra chain min 12 30 cm Burner7.1 U-TubeConfiguration SECTION 7 OPTIONAL HEATER ACCESSORIESCut/Pinch Hazard Edges are sharpU-tube,Standard FIGURE 18 U-TubeHeater Assembly OverviewU-tube U-tubeFIGURE 19 U-TubeHeater Layout Overview FIGURE 20 U-TubeLayout Overview Continued Step 7.2.3 Reflector Joint Installation Step 7.2.2 Elbow InstallationStep 7.2.4 Reflector Joint Installation Reflector Reflector JointSECTION 7 OPTIONAL HEATER ACCESSORIES Install reflectorStep 7.2.5 Reflector Joint Detail FIGURE 21 Reflector Joint DetailStep 7.3.1 Bracket Installation Step 7.3.2 Side Reflector Installation7.3 Reflector Side Extension Step 7.4.1 Shield Support Strap Assembly 7.4Lower Clearance Shield InstallationSECTION 7 OPTIONAL HEATER ACCESSORIES DescriptionStep 7.5.2 Frame Shield Installation Step 7.6.3 Grille Installation Step 7.6.2 Grille End Cap InstallationCarbon Monoxide Hazard SECTION 8 VENTINGCut/Pinch Hazard Edges are sharp8.3 Horizontal Venting 8.2 Unvented Operation8.4 Vertical Venting 8.5 Unvented Operation Tube Termination8.8 Vertical Ventilation 4 10 cm Pipe 8.7 Horizontal Ventilation 4 10 cm PipeSIDE VIEW Combustible or8.9 Common Side Wall Venting RequirementsHeaters must be of the same BTU output 8.10 Common Vertical Venting Heaters must be of the same BTU outputRequirements 8.11.1 Length Requirements 8.11 Outside Combustion Air SupplyRequirements RequirementsSECTION 9 GAS PIPING Gas hose can crack when twistedFire Hazard Gas hose moves during normal operationINCORRECT POSITIONS WRONG INSTALLATION when attaching gas hoseFIGURE 23 Gas Connection with Flexible Gas Hose CORRECT POSITIONSSECTION 10 WIRING DANGERDisconnect electric before service or maintenance 10.1 Line Voltage Thermostat Wiring10.2 Low Voltage Thermostat Wiring Pressure Switch 10.3 Internal WiringDSI Ignition Module BLUE ElectrodeConnect wires together with heater before service SECTION 11 OPERATION AND MAINTENANCEbefore service or during installationFor best performance, the gas, electrical, thermostat connections, tubing, venting, suspensions and overall heater condition should be inspected thoroughly Installation Code and Annual Inspections 11.5 Maintenance ChecklistThe Vicinity of the Heater See Page 4, SectionElectrode Burner Cup and OrificeThermostat See Page 43, SectionDisconnect electric before service or maintenance SECTION 12 TROUBLESHOOTINGheater before service before service or12.1 Troubleshooting Flow ChartSECTION 12 TROUBLESHOOTING 12.2 Manifold Gas Pressure Setting Natural PropaneTop View of Heater DANGER SECTION 13 REPLACEMENT PARTSTOP VIEW REAR VIEWPart Number Description14.1 Material Specifications 14.1.1 Reflectors SECTION 14 GENERAL SPECIFICATIONS14.2 Heater Specifications 14.2.1 Ignition DIMENSIONSROBERTS-GORDONLLC WILL PAY FOR WARRANTY IS VOID IFROBERTS-GORDONLLC WILL NOT PAY FOR LIMITATIONS ON AUTHORITY OF REPRESENTATIVESPage About the Installer OWNER WARRANTY REGISTRATION CARDPurchased From if different than installer Type of Installation check onePage Page clearance Maintainthe side clearance below