DESIGN FEATURES

12.Power Terminals – The power and ground are nickel-plated captive c-clamp wire connectors and will accommodate up to 4 AWG wire.

13.Fuses – These ATC fuses are easily accessible in case of failure.Always replace fuses with same type and rating. See Specifications for fuse ratings.

14.Infrasonic Filter – A 28Hz High Pass filter designed to prevent frequencies below the audio range from being applied to the subwoofer from the amplifier. Consequently improving subwoofer performance and power handling.

INSTALLATION

INSTALLATION CONSIDERATIONS

The following is a list of tools needed for installation:

Volt/Ohm Meter Wire strippers Wire crimpers Wire cutters

#2 Phillips screwdriver Battery post wrench

Hand held drill w/assorted bits 1/8" diameter heatshrink tubing Assorted connectors

Adequate Length—Red Power Wire Adequate Length—Remote Turn-on Wire Adequate Length—Black Grounding Wire

This section focuses on some of the vehicle considerations for installing your new amplifier. Pre-planning your system layout and best wiring routes will save installation time.When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments.

CAUTION:If you feel unsure about installing this system yourself, have it installed by a qualified technician.

CAUTION:Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

Before beginning any installation, follow these simple rules:

1.Be sure to carefully read and understand the instructions before attempting to install the unit.

2.For safety, disconnect the negative lead from the battery prior to beginning the installation.

3.For easier assembly, we suggest you run all wires prior to mounting your unit in place.

4.Route all of the RCA cables close together and away from any high current wires.

5.Use high quality connectors for a reliable installation and to minimize signal or power loss.

6.Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7.Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

8.Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

9.ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power wire within 18" (45.7 cm) of the battery terminal.

10.When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle.

5

Page 4 Page 6
Page 5
Image 5
Rockford Fosgate P325.I, P600..I bd manual Installation Installation Considerations
Page 4 Page 6

P325.I, P600..I bd specifications

Rockford Fosgate has long been synonymous with high-performance audio equipment, and their series of amplifiers, namely the P325.1 and P600.1bd, continue to uphold this legacy. Engineered to deliver uncompromising sound quality and powerful output, these amplifiers are ideal for car audio enthusiasts looking to elevate their in-car listening experience.

The P325.1 is a compact monoblock amplifier designed to supply robust power to subwoofers. With a power output of 325 watts RMS at 2 ohms, it strikes an excellent balance between size and performance. This amplifier features a high-pass crossover that can be used to filter out unwanted frequencies, ensuring that your subwoofer receives only the bass it needs to perform optimally. The adjustable subsonic filter further allows users to tune the amplifier according to their specific audio preferences, ensuring clean and powerful bass reproduction.

On the other hand, the P600.1bd ups the ante with a significant power output of 600 watts RMS at 1 ohm, making it well-suited for larger subwoofers or more demanding sound systems. This amplifier incorporates Rockford Fosgate's innovative Class BD technology, which allows for higher efficiency and improved thermal performance. The Class BD design also minimizes distortion at higher volumes, rendering a cleaner sound that preserves the integrity of the audio source. The P600.1bd includes a variable low-pass filter and phase switch, enabling users to fine-tune the soundstage according to their vehicle's acoustics.

Both amplifiers are designed with premium components, featuring a cast aluminum chassis that not only enhances durability but also promotes effective heat dissipation. This is crucial for ensuring the longevity of the amplifiers during prolonged use. Additionally, these models come equipped with RCA inputs, screw-type terminals for easy wiring, and a sleek design that fits seamlessly into any vehicle setup.

In conclusion, the Rockford Fosgate P325.1 and P600.1bd amplifiers are exceptional choices for audio aficionados seeking powerful and precise sound amplification. With advanced technology, customizable settings, and robust construction, they stand out as reliable components for any high-performance car audio system. Whether you are a casual listener or a dedicated audiophile, these amplifiers offer a pathway to an enhanced listening experience on the road.
Top Page Image Contents