Runco VX-22I - page 49

Runco VX-22i Installation/Operation Manual 35

PRELIMINARY

Connecting an External IR

Receiver to the VX-22i

If infrared signals from the remote control cannot reach the projector due to excessive

distance or obstructions such as walls or cabinet doors, you can connect an external IR

receiver to the WIRED REMOTE input on the VX-22i to extend the range of the remote

control. See Figure 3-17.

Figure 3-17. External IR Receiver Connection

Connecting to AC PowerProjector: Plug the female end of one power cord into the AC receptacle on the rear of

the VX-22i (AC 100V ~ 240V). Then, connect the other end to your AC power source.

AutoScope Lens Motor: With AutoScope-equipped projectors, an additional power

cord is provided for the lens motor. Plug the female end of the AC power cord into the AC

input on the rear of the lens motor assembly. Connect the other end to a 110 VAC power

source.

When an external IR receiver is connected to the wired IR input, the

built-in IR sensor on the VX-22i is disabled.

Rear Panel

WIRED REMOTE

WIRED REMOTE

Service port.

Not for user

access

Ring = +5V

Tip = IR Input

Sleeve = Ground

(3.5-mm

mini phono

plug)

IR Receiver

Remote

Control

FOCUS LENSZOOM

LIGHTOFF

ON

VIDS

-VIDH

DMI1

HD2

SOURCE

PICTURE MEMORY

ASPECT RATIO

HD1

INFO

ENTER

EXITM

ENU

BRT

CUST1CUST2

CONTC

OLT

INT

HD3

HDMI2

ISF

DAY

ISF

NIGHT

16:9IWIDE

LBOX

4:3

CINEMAIWIDE

2.35

FOCUSZOOM

2

1

5

46

3

9

80

7

LENS

Note

The input voltage to the AutoScope lens motor must be between

100 and 120 VAC. Do not connect the AutoScope lens motor

to a 200-240 VAC power source!

Caution

Contents

Main Page TWO YEAR LIMITED WARRANTY For Projectors, Video Processors and Controllers Page RUNCO VIDEO-PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS Important Safety Instructions Compliance Information Page Page Page Page Page Page Page 1.1 About This Manual 1. Introduction 1.2 Using This Manual DANGER! WARNING 1.3 Description, Features and Benefits Page 2.1 VX-22i at a Glance 2. Controls and Functions 2.2 VX-22i Rear Panel Page 2.3 VX-22i Rear Connector Panel 10 9 8 7 6 5 4 3 2 1 Page 10 Runco VX-22i Installation/Operation Manual 2.4 VX-22i Remote Control Figure 2-4. VX-22i Remote Control LIGHT OFF ON SOURCE PICTURE MEMORY ASPECT RATIO Page Page 3.1 Remote Control 3.2 Quick Setup Table 3-1. Installation Overview 3.3 Installation Considerations Table 3-2. Projector Installation Options Table 3-3. VX-22i Lens Options and Throw Ratios Ceiling Installation Floor Installation Figure 3-4. Horizontal Lens Shift (EXAMPLE ONLY) Table 3-4. VX-22i Vertical and Horizontal Lens Shift Limits 3.4 Installing the Primary Projection Lens Page 3.5 Installing the Optional CineWide Lens Mount Page Page Page Page 3.6 Mounting the VX-22i 3.7 Connections to the VX-22i Page Page Page Page to Automation/ Control System or PC Page Page 3.8 Turning on the Power 3.9 Adjusting the Picture Orientation VX22i Component RCA 16:9 480I 3.10 Primary Lens Adjustments 3.11 Installing and Adjusting the CineWide Anamorphic Lens Page Page Page Page Wrong Position Correct Position Page 4. Operation Figure 4-1. VX-22i OSD Menu Structure Input Source Calibration Memory Presets Input Position 7 Table 4-1. Aspect Ratio Settings Table 4-1. Aspect Ratio Settings (continued) Page Page Page Page 7 Page Page Page Page 5.1 Lamp Replacement 5. Maintenance and Troubleshooting WARNING 5.2 Filter Replacement Side Filter Access Panel 5.3 Troubleshooting Tips Table 5-1. Troubleshooting Chart Page 6.1 RS-232 Connection and Port Configuration 6.2 Serial Command Syntax Table 6-1. Serial Commands and Responses Table 6-1. Serial Commands and Responses (continued) Page 7.1 VX-22i Specifications Table 7-1 lists the VX-22i specifications. Table 7-1. VX-22i Specifications Table 7-1. VX-22i Specifications (continued) Runco VX-22i Installation/Operation Manual 69 7.2 VX-22i Dimensions Figure 7-1 shows the VX-22i dimensions (all dimensions are in inches). Figure 7-1. VX-22i/CineWide with AutoScope Dimensions 7.3 Supported Timings Table 7-2 lists the signal types supported by each input on the VX-22i. Table 7-2. Supported Signal Timings by Input Table 7-2. Supported Signal Timings by Input (continued)