Runco VX-22I 3.2 Quick Setup

14 Runco VX-22i Installation/Operation Manual

PRELIMINARY

3.2 Quick Setup

Table 3-1 gives a quick overview of the VX-22i installation process. The sections following

this one provide detailed instructions.

Installation should be performed by a qualified custom video

installation specialist.

Table 3-1. Installation Overview

Step Procedure For Details, Refer to

page...

1Choose a location for the projector 15

2If installing a VX-22i/CineWide or VX-22i/CineWide

with AutoScope: Install fixed CineWide base plate or

AutoScope lens motor

22

3Mount the projector 27

4Connect signal sources to the projector 28

5Connect external controller to RS-232 port (optional) 33

6Connect 12-volt trigger outputs to AutoScope lens motor

and/or other equipment (optional)

34

7Connect projector and lens motor (if present) to AC power

and power up

35

8For rear-screen and/or ceiling-mount installations, select

the proper picture orientation

36

9Primary lens adjustments: projected image size (zoom),

position (shift) and focus

17, 37

10 Install CineWide anamorphic lens (optional) 38

11 CineWide lens adjustments: position, pitch (angle),

geometry and focus

40

12 Projector calibration: adjust the following for each input;

save settings when finished:

• Aspect ratio

• Brightness

• Contrast

• Color level

• Tint

• Input position

47

Note

Contents

Main Page TWO YEAR LIMITED WARRANTY For Projectors, Video Processors and Controllers Page RUNCO VIDEO-PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS Important Safety Instructions Compliance Information Page Page Page Page Page Page Page 1.1 About This Manual 1. Introduction 1.2 Using This Manual DANGER! WARNING 1.3 Description, Features and Benefits Page 2.1 VX-22i at a Glance 2. Controls and Functions 2.2 VX-22i Rear Panel Page 2.3 VX-22i Rear Connector Panel 10 9 8 7 6 5 4 3 2 1 Page 10 Runco VX-22i Installation/Operation Manual 2.4 VX-22i Remote Control Figure 2-4. VX-22i Remote Control LIGHT OFF ON SOURCE PICTURE MEMORY ASPECT RATIO Page Page 3.1 Remote Control 3.2 Quick Setup Table 3-1. Installation Overview 3.3 Installation Considerations Table 3-2. Projector Installation Options Table 3-3. VX-22i Lens Options and Throw Ratios Ceiling Installation Floor Installation Figure 3-4. Horizontal Lens Shift (EXAMPLE ONLY) Table 3-4. VX-22i Vertical and Horizontal Lens Shift Limits 3.4 Installing the Primary Projection Lens Page 3.5 Installing the Optional CineWide Lens Mount Page Page Page Page 3.6 Mounting the VX-22i 3.7 Connections to the VX-22i Page Page Page Page to Automation/ Control System or PC Page Page 3.8 Turning on the Power 3.9 Adjusting the Picture Orientation VX22i Component RCA 16:9 480I 3.10 Primary Lens Adjustments 3.11 Installing and Adjusting the CineWide Anamorphic Lens Page Page Page Page Wrong Position Correct Position Page 4. Operation Figure 4-1. VX-22i OSD Menu Structure Input Source Calibration Memory Presets Input Position 7 Table 4-1. Aspect Ratio Settings Table 4-1. Aspect Ratio Settings (continued) Page Page Page Page 7 Page Page Page Page 5.1 Lamp Replacement 5. Maintenance and Troubleshooting WARNING 5.2 Filter Replacement Side Filter Access Panel 5.3 Troubleshooting Tips Table 5-1. Troubleshooting Chart Page 6.1 RS-232 Connection and Port Configuration 6.2 Serial Command Syntax Table 6-1. Serial Commands and Responses Table 6-1. Serial Commands and Responses (continued) Page 7.1 VX-22i Specifications Table 7-1 lists the VX-22i specifications. Table 7-1. VX-22i Specifications Table 7-1. VX-22i Specifications (continued) Runco VX-22i Installation/Operation Manual 69 7.2 VX-22i Dimensions Figure 7-1 shows the VX-22i dimensions (all dimensions are in inches). Figure 7-1. VX-22i/CineWide with AutoScope Dimensions 7.3 Supported Timings Table 7-2 lists the signal types supported by each input on the VX-22i. Table 7-2. Supported Signal Timings by Input Table 7-2. Supported Signal Timings by Input (continued)