RULES FOR SAFE OPERATION
READ AND UNDERSTAND ALL INSTRUCTIONS
1.KNOW YOUR POWER TOOL. Safe operation of this power tool requires that you read and understand this operator’s manual and all labels affixed to the tool. Learn its applications and limitations as well as the potential hazards.
WARNING:
Do not connect your drill press to a power source until you have assembled and adjusted the drill press as described in this manual and have read and understood all precautions and operating instructions in the manual and printed on the tool.
WARNING:
When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury. Use common sense. Some of these basic safety precautions include the following:
SAFETY PRECAUTIONS
2.KEEP GUARDS IN PLACE and in good working order.
3.REMOVE ADJUSTING KEYS AND WRENCHES. Get in the habit of checking to see that hex keys and adjusting wrenches are removed from the tool before turning it on.
4.KEEP THE WORK AREA CLEAN. Cluttered work areas and work benches invite accidents.
5.DO NOT USE IN DANGEROUS ENVIRONMENTS. Do not use power tools near gasoline or other flammable liquids, in damp or wet locations, or expose them to rain. Keep the work area well lighted.
6.KEEP CHILDREN AWAY FROM POWER TOOLS. All visitors should be kept at a safe distance from the work area.
7.MAKE THE WORKSHOP
8.DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed.
9.USE THE RIGHT TOOL. Do not force the tool or attachment to do a job for which it was not designed.
10.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. A wire gage size (A.W.G.) of at least 16 is recommended for an extension cord 100’ or less in length. A cord exceeding 100’ is not recommended.
11.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that could get caught in moving parts.
12.ALWAYS WEAR SAFETY GLASSES WITH SIDE SHIELDS. Everyday eyeglasses have only impact resistant lenses; they are not safety glasses.
13.PROTECT YOUR LUNGS. Wear a face or dust mask if the drilling operation is dusty.
14.PROTECT YOUR HEARING. Wear hearing protection during extended periods of operation.
15.SECURE THE WORK. Use clamps or a vise to hold the work when practical. It’s safer than using your hand and frees both hands to operate the tool.
16.DO NOT OVERREACH. Keep proper footing and balance at all times.
17.MAINTAIN THE TOOL WITH CARE. Keep bits sharp and clean for the best and safest performance. Follow instructions for lubricating and changing accessories.
18.DISCONNECT POWER TOOLS BEFORE SERVICING or before changing accessories such as blades, bits and cutters.
19.REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in the OFF position before plugging in the tool.
20.USE ONLY ACCESSORIES RECOMMENDED BY THE MANUFACTURER. Consult this operator’s manual for recommended accessories. Using improper accessories may cause risk of injury.
21.NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the bit is unintentionally contacted.
22.PERIODICALLY CHECK FOR WORN OR DAMAGED
PARTS. Check for alignment of moving parts, binding of moving parts, breakage of parts, loose mounting brackets, and any other conditions that may affect operation. A guard or any other part that is damaged should be properly repaired or replaced. Before the tool is used again, make sure that the repaired or replaced part is operating properly and performing its intended function.
23.NEVER LEAVE TOOL RUNNING UNATTENDED. Turn the power off. Do not leave tool until it comes to a complete stop.
24.DO NOT ABUSE CORD. Never yank the cord to disconnect it from the receptacle. Keep the cord from heat, oil, and sharp edges.
25.KEEP BITS CLEAN AND SHARP. Sharp bits minimize stalling. Dirty and dull bits may cause misalignment of the material and possible operator injury.
26.KEEP HANDS AWAY FROM WORK AREA. Keep hands away from the bit. Restrain any loose clothing, jewlery, long hair, etc. that may become entangled in the bit.
27.KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline,
28.STAY ALERT. Never operate a power tool when tired or while under the influence of drugs, alcohol or medication.
4
