MDR10 Input and Output Connections
EXTERNAL OUTPUT JACKSThe MDR10 features several output connectors allowing you to interface a variety of external devices. A stereo recording device such as a cassette recorder can be connected to the 2 Track jacks, and power amplifiers can be connected to the CONTROL ROOM and MAIN output jacks.
5 LEFT/RIGHT MIXIn a live sound application the LEFT/ RIGHT MIX outputs are connected to a power amplifier or powered speak- ers. In a recording application, the LEFT/ RIGHT MIX outputs are used to connect a stereo device such as computer sound card, DAT, or cassette recorder.
6 3/4 OUTPUTIn a live sound application, the 3/4 bus outputs are connected to a power amplifier or powered speakers. In a recording application, the 3/4 outputs are used to connect a stereo device such as computer sound card, DAT, or cassette recorder.
7 FX RET 1 LEFT/RIGHTThe FX RET 1 LEFT/RIGHT are stereo inputs that are generally used to connect the outputs of an effects processor, but can also accept the signal from any line level source like a keyboard, recorder and even another mixer. The signal connected to the FX RET 1 LEFT/RIGHT will feed the main LEFT/RIGHT MIX bus. The overall level is controlled by the FX RETURN 1 knob located in the master section on the front panel
8 FX RET 2 LEFT/RIGHTThe FX RET 2 LEFT/RIGHT are stereo inputs that are generally used to connect the outputs of an effects processor, but can also accept the signal from any line level source like a keyboard, recorder and even another mixer. The signal connected to the FX RET 2 LEFT/RIGHT will feed the main LEFT/RIGHT MIX bus. The overall level is controlled by the FX RETURN 2 knob located in the master section on the front panel
9 AUX 1 Output10
11
The signal present at the AUX 1 output is sent from the AUX 1 bus, which is fed from the AUX 1 send on the input channels. The AUX 1 output can be used as the MONITOR MIX bus in a live sound situation by connecting the output to a power amp and monitor speaker.
AUX 2 OUTPUTThe AUX 2 output is used to send a signal to an external signal processor such as a delay or reverb. The signal present at the AUX 2 output is sent from the AUX2/DSP bus, which is fed from the AUX2/DSP send on the input channels.
CONTROL ROOM LEFT/RIGHT12
13
The Control Room outputs are used to connect a studio monitor system. The Control Room outputs have the same output as the L/R MIX, however, the level can be adjusted independently from the main mix using the C ROOM/HEADPHONES control.
MONO OUTPUTThe Left and Right Mix outputs are summed together and sent to the MONO output. The level of the Mono signal can be adjusted using the MONO OUT level control located just below the connector and used to feed a speaker zone in a fixed installation.
|
|
|
|
| ON |
|
|
| ON | ||
AC INLET |
| 13 |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
Connected the supplied Samson AC adapter here. Before connecting |
|
|
|
| l |
|
|
| l |
|
|
|
|
|
| o |
|
|
| o |
|
| |
the supply, make sure that the MDR10 POWER and PHANTOM |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |
POWER switches are in the off position. |
|
|
|
|
|
|
|
|
|
|
|
| POWER INPUT | POWER |
| PHANTOM | |||||||
|
| MADE IN CHINA | www.samsontech.com |
15