11PAN – Controls the channel’s balance between left and right in the stereo bus.

12SOLO Switch (Input Channels) – Back-lit LED switch used to assign the channel to the SOLO bus.

13MUTE 3/4 – LED, back-lit switch used to Mute the input chan- nel from the Main Left and Right mix bus, and at the same time, assign the channel to the 3/4 output bus.

14FADER – 60 mm audio taper fader provides smooth control over level changes.

15MIC INPUT – XLR input connector for the input channel’s Low- Noise Microphone pre-amp.

16LINE INPUT – 1/4-inch TRS ( TIP RING SLEEVE) input con- nector for the input channel’s balanced Line level inputs.

17LOW FREQUENCY (Stereo Channels) - Controls the low band of the Channel Equalizer, +/- 15 dB at 80Hz.

18HIGH FREQUENCY (Stereo Channels) - Controls the high band of the Channel Equalizer, +/- 15 dB at 12KHz.

19AUX 1/2 Switch (Stereo Channels) - The auxiliary send on the Dual/Mono channels can be set to either the AUX 1 or AUX 2 bus by using the back-lit, AUX1/2 switch.

20MIC LINE – Combination Input connector for the Line or Low- Noise Microphone Inputs on the stereo channels.

21FX RET 1 (L/R Jacks) – Balanced inputs on 1/4-inch TRS con- nectors for connecting external line level signal like those from external effects processors.

223/4 OUTPUT – Balanced outputs on 1/4-inch TRS connectors that carry the signals from the 3 and 4 mix bus.

23MIX (L R Jacks) – Balanced outputs on 1/4-inch TRS connec- tors that carry the signals from the Left and Right Main mix bus.

24AUX 1 - 1/4-inch TRS output connector for Auxiliary 1.

25CONTROL ROOM – Left and Right output connectors for con- necting a monitor system.

26AUX 2– Output connector for Auxiliary 2.

27MONO OUT – The Left and Right main Mix outputs are summed together to a monaural signal and sent out this con- nector.

28FX RETURN 2 (L R Jacks) – Balanced inputs on 1/4-inch TRS connectors for connecting external line level signals like those from external effects processors.

29MONO OUT LEVEL – Used to set the volume of the MONO mix.

302 TK LEVEL - Control used to adjust the volume of the 2-track input.

312 TRACK INPUTS – Connect a DAT, Cassette, Mini Disk or Hard Disk Recording system.

Front Panel Layout

32FX TO AUX – When this switch is engaged, the FX RETURN 2 is sent to the AUX 1 output allowing the effects, external or internal, to be heard in the monitor mix.

332 TRACK OUTPUTS – Connect a DAT, Cassette, Mini Disk or Hard Disk Recording system.

34PHANTOM – Indicates that the 48 Volt Phantom Power is on.

35FX RETURN 2 Knob – Used to mix in level of the external effects connected to the FX RETURN 2 inputs.

36POWER – Indicates the MDR10 is powered up.

37SOLO LED – Indicates SOLO is selected.

38PFL LED – Indicates the SOLO is in PFL (Pre-Fader Level) mode.

39SOLO Switch (FX RETURN 2) – Back-lit LED switch used to assign the FX RETURN 2 to the SOLO bus.

40OUTPUT METER - Twelve segment display with VU ballistics indicates main Mix level.

41DSP PEAK LED - LED light illuminates when the signal sent to the internal DSP is clipped.

42SOLO/PFL Switch – Used to change the operating mode of the SOLO bus from SOLO to PFL (Pre Fader Listen).

43SOLO DEFEAT Switch – This global control back-lit, switch is used to disconnect all channels from the SOLO bus.

44MIX MUTE Switch – When the switch pressed, the red LED lights indicating the Main Left and Right outputs are fully attenuated.

45MIX FADERS- Used to control the overall volume of the Left and Right main Mix outputs.

46HEADPHONE JACK – Connect stereo headphones here.

47C ROOM/HEADPHONE – Adjusts the volume of the control room speakers or headphones.

48SOLO LEVEL – A rotary control knob used to set the overall volume of the SOLO bus.

49MIX/2TK– Switches between the main Mix and the 2 Track in the Control Room output.

50OUTPUT 3 & 4 FADERS – Used to control the overall volume of the 3 and 4 mix outputs.

513/4 TO MIX Switch – When engaged, the LED lights and the input channels which are a assigned to 3/4 will be mixed together with the Main Left and Right Outputs.

52SOLO Switch (3/4 Bus) – Back-lit LED switch used to assign the 3/4 Bus to the SOLO bus.

53DSP PRE-SET SELECT Knob – Used to switch between the 8 pre-sets of the internal DSP effects processor.

54SOLO Switch (FX RETURN 1) – Back-lit LED switch used to assign the FX RETURN 1 to the SOLO bus.

55FX RETURN 1 – Used to mix in level of the external effects connected to the FX RETURN 1 inputs.

5