Scart Connector AV1/AV2/AV3, PC Input Connector | Samsung 4240

BN68-00597A-01 4/2/04 6:40 PM Page 64

Pin Configurations

ENG

SCART Connector (AV1/AV2/AV3)

➢Pins 5, 7, 9, 11, 13, 15 and 16 are used for RGB processing and are only wired on the AV1 or AV2 or AV3 connector.

Pin

Signal

Pin

Signal

1Audio output R

2Audio input R

3Audio output L

4Audio chassis return

5Video chassis return (RGB blue)

6Audio input L

7RGB blue input

8Switching voltage

9Video chassis return (RGB green)

10 AV-Link (Ext 1)

11 RGB green input

12	-
13	Video chassis return (RGB red)
14	-

15RGB red input

16Blanking signal (RGB switching)

17Video chassis return

18Blanking signal ground

19Video output

20Video input

21Screening/chassis return

PC Input Connector
(15Pin)
Pin	PC IN
1	Red (R)
2	Green (G)
3	Blue (B)
4	Grounding
5	Grounding (DDC)
6	Red (R) Grounding
7	Green (G) Grounding
8	Blue (B) Grounding
9	Reserved
10	Sync Grounding
11	Grounding
12	Data (DDC)
13	Horizontal sync.
14	Vertical sync.
15	Clock (DDC)

DVI Input Connector
(24Pin)
Pin	Signal
1	T.M.D.S. Data2-
2	T.M.D.S. Data2+
3	T.M.D.S. Data2/4 Shield
4	T.M.D.S. Data4-
5	T.M.D.S. Data4+
6	Clock (DDC)
7	Data (DDC)
8	Not Connected
9	T.M.D.S. Data1-
10	T.M.D.S. Data1+
11	T.M.D.S. Data1/3 Shield
12	T.M.D.S. Data3-
13	T.M.D.S. Data3+
14	+5V Power
15	5V Grounding
16	Hot Plug Detect
17	T.M.D.S. Data0-
18	T.M.D.S. Data0+
19	T.M.D.S. Data0/5 Shield
20	T.M.D.S. Data5-
21	T.M.D.S. Data5+
22	T.M.D.S. Clock Shield
23	T.M.D.S. Clock+
24	T.M.D.S. Clock-

64

Image 64

Samsung 4240 manual Scart Connector AV1/AV2/AV3, PC Input Connector, 15Pin, DVI Input Connector, 24Pin

Contents

PDP-TELEVISION Warranty Screen Image retentionCell Defect Height Owner’s Instructions Power CordSold Separately Contents Symbols Actual configuration on your PDP may be different Depending on your model Depending on your model For further details about connection, refer to pages 55~59 Infrared Remote Control Inserting the Batteries in the Remote Control Angle of the PDP can be up to 20 degrees left/right Installing the Display on the Wall Attachment Panel Wall Mount Bracket Plastic Hanger Connecting External Devices to the PDP Connecting to an Aerial or Cable Television Network Connecting a Satellite Receiver or DecoderRear of the PDP Use the 3M/5M/7M cable supplied by Samsung Switching On and Off Mains lead is attached to the rear of your PDP Becoming Familiar with the Remote Control Remote control is used mainly toChange channels and adjust the volume Display the on-screen menu system Setting Up Your Remote Control Plug & Play Feature To start the search, press the Enter button If you want to reset this feature Choosing Your Language Storing Channels Automatically See Auto PAL Secam or Auto NT3.58 NT4.43 PAL60 Storing ChannelsManuallyBG DK I L Channel mode Skipping Unwanted Channels Skipping unwanted channels Sorting the Stored Channels Assigning Names to Channels Using the LNA Low Noise Amplifier Feature Activating the Child Lock Activating the child lock Changing the Picture Standard Displaying InformationDynamic Standard Movie Custom High Middle Low Custom Adjusting the Picture Settings Custom Options available in PC, DVI Mode ContrastBrightness, Sharpness Colour Tone Cool2, Cool1, Normal, Warm1, Warm2 Adjusting the Picture Settings PC or DVI Mode Custom PC mode only Colour1 Colour2 Colour3 Setting the Picture PC Mode Preset to the PC mode by using the Source button Setting the Picture PC Mode Colour System and Sound System settings are correct Using the Fine TuneIf reception is weak, you can fine tune a channel manually Viewing the Channel Scan Picture Freezing the Current PictureResult Main menu is displayed Result Options available in the Channel group are PC to DVI Mode Positioning and Sizing the screen using ZoomSelecting the Picture Size Selecting the Film Mode DNIeTM Digital Natural Image engine Setting the Melody Sound Setting the Blue ScreenSelect the option Off or On Table of PIP Settings Viewing the Picture In Picture PIP Easy functions of remote control Buttons FeaturePicture Button after changing the sub Using the Digital NR Digital Noise Reduction Feature Changing the Sound Standard Standard Music Movie Speech Custom Adjusting the Sound Settings Adjusting the Volume Automatically Selecting the Internal Mute Setting the TruSurround XTStereo Selecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Switching the Television On and Off Automatically Absent Power Off AV1, AV2, AV3, S-Video1,S-Video2,Component1 Viewing an External Signal SourceSatellite STB, AV Receiver, DVD Receiver, Game Redirecting an Input to the External Output Teletext Feature Contents Displaying the Teletext Information Press the TTX/MIX button again Selecting Display Options To display Press Selecting a Teletext TeleWeb Feature Option Using the TeleWeb Menu after Displaying the TeleWeb Bookmarking the currentEntering the bookmarked URL Opening the Home Easy Accessing the TeleWeb Service via the Remote Control TeleWeb Connecting to the External Devices Input/Output SpecificationRear of the TV Input Connecting to the S-Video Input Rear of the TV Side of the TV Connecting to the DVI Input Connecting to the PC Input Connecting to the Component Input Connecting Additional Speakers Connecting the Home Theater System Connecting and Using the Home Theater SystemTo Display the DVD Home Theater Installing the Speakers This speaker installation guide is for the 4240 Model How to Assemble the Speakers Wall Mount Bit colour Shown at left is a typical screen for Display dialog box Video Signal Dot x Line Vertical Horizontal NVidia chipset Scart Connector AV1/AV2/AV3 PC Input ConnectorDVI Input Connector 15Pin Power button Check the picture contrast and brightness settingsCheck the volume Normal picture but no sound Check the volume Programming the Remote Control for Other Components 003, 024019, 023 Wamer amex NEC 040, 047, 050, 052, 060, 063, 065, 066, 067 After Sales Service